Remotec 1279041 Dépliant

Congratulations! Your Universal Remote Control (URC) is a state-of-the-art 
device which integrates many different infra-red remote controls to deliver 
instant A/V action to your fingertips.

Before operating the remote, please read thoroughly (1) the inside of the 
coversheet and (2) this manual. Then store them for future reference.

Alkaline batteries are recommended. The batteries required are 2 x AAA 1.5V 
or equivelent.
1. Remove the battery cover on the back of your URC.
2. Insert the batteries observing the "+/-" marks inside the battery 

compartment.

3. Push the battery cover back in place.

NOTE: 
The memory inside the remote will retain its settings for short periods of time 
with the batteries removed (When changing batteries for instance).

You may setup the URC by following the code entering instructions.

1. Referring to the DEVICE CODE LIST, look up the 4-digit Device Code 

which corresponds to the brand of your A/V equipment. If there is more 
than one Device Code listed under your brand, start from the first code.

2. Press the desired Device Mode Key (e.g. TV).
3. Hold down "CH +" and "VOL -" on the URC simultaneously for 2 seconds 

until the indicator light under the power key lights up.

4. Use the number keys "0" - "9" to enter your 4-digit Device Code. The 

indicator should go out after the 4th digit is entered.

Turn on your device (e.g. TV), then try the function keys on the URC. If your 
device (e.g. TV) responds to your activated function correctly, you have 
entered the right Device Code. Otherwise, repeat the above steps with the 
next available Device Codes until your device (e.g. TV) responds to your 
activated function, and most keys work correctly.

* Simply repeat the above procedures to enter the Device Codes for your 

DVD and AUX devices. (Remember to press the correct Device Mode Key 
in step 2 above)

If the indicat

s twice in step 4, a wrong 

Device Code has been entered. You are required to repeat step 2 to 4 
again.

Suggestion :
-

If you cannot find a correct Device Code for your equipment, see   .  
HOW TO SET UP THE URC - By Searching Through the Library.

-

For future reference you are recommended to take a note of your Device 
Codes in the space provided on the product's back label after setting up 
the URC correctly.

or light under the power key flashe

2

4

If you cannot identify a correct Device Code for your equipment from the 
Device Code list, you may search for the code in the library:-

1. Turn on your device manually (e.g. TV).
2. Press a desired Device Mode Key (e.g. TV).
3. Hold down "CH +" and "VOL -" on the URC simultaneously for 2 seconds 

until the indi

ts up.

4. Enter a corresponding Magic Search Code from the following table. The 

indicator ligh

ould go out 

.

(e.g. press "TV" device mode key, then press "CH +" and "VOL -", and 
enter TV Magic Search Code 0001.)

5. Press the same desired device mode key again as in step 2 above. (e.g. TV)
6. Hold down "CH +" & "VOL -" simultaneously for 2 seconds until the 

indicator 

 and your URC is ready to start 

searching.

7. Aim the URC at your device (e.g. TV), press the "   " key slowly and 

repeatedly until the device has been turned off.
Once your device has been turned off, immediately press Device Mode Key 
(

* Simply repeat the above setup procedures to search for the Device Code 

for your VCR, STB, DVD or CTV. (Remember to press the correct Device 
Mode Key and correct Magic Search Code in step 2-5 above)

cator under the power key ligh

t under the power key sh

after the 4th digit is 

entered

light under the power key lights up,

e.g. TV) to lock the code, the indicator light under the power key will go out.

-

If the power on/off function of your device is not infra-red controlled, you 
need to follow steps 2 to 6 above and start searching:-

-

Press "   " and another function key alternately until your device 
responds to the expected function, then press the same Device Mode 
Key (e.g. TV) to lock in the code.

e.g. Press "     " & "1" alternately, or ;

Press "     " & "    " alternately.

-

DVD, CTV and other device codes can be searched for and locked into 
any device modes. Simply press the corresponding device mode key in 
step 2 & 5 and enter an appropriate Magic Search Code for your DVD, 
CTV and other devices.

-

Each time you press the "    ", the URC will skip to the next code and 
send out a POWER signal trying to turn off your device. 

If you fail to stop pressing "    " in time when your device has been turned

code.

-

If the indicator

s twice after your 

pressing of "    " key, you are already at the last code of the library. Press 
"CH +" and "VOL -" to resume the URC and repeat the above 
procedures carefully to search again.

 

off, turn your device on again immediately. Before the indicator under the 
power key goes out, press "    "on the URC to skip backward. Repeat 
step 7 above and lock in the 

 light under the power key flashe

5

Once you have set up the URC for your A/V equipment, it works like your 
original remote control. To operate, just aim it at your equipment, press an 
appropriate device mode key and invoke the desired function by pressing a 
corresponding key on the URC. The indicator light under the power key 
flashes during signal transmission and as confirmation of key touch.

Punch through channel allows you to operate channel up and down without 
having to switch the device modes repeatedly even when your URC is in other 
operating modes.

To activate the punch through channel setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "CH +" key.
3. Press desired Device Mode Key of the device you want to change the 

channel on.

4. Release "CH +"  (the indicator light under the power key flashes once if the 

setting is activated).

To deactivate the punch through channel setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "CH -" key.
3. Press desired device Mode Key of the device you want to change the 

channel on.

4. Release "CH -" (the indicator light under the power key flashes twice if the 

setting is activated).

Punch through volume allows you to operate volume up and down without 
having to switch the device modes repeatedly even when your URC is in other 
operating modes.

To activate the punch through volume setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "VOL +" key.
3. Press desired Device Mode Key of the device you want to change the 

volume on.

4. Release "VOL +" (the indicator light under the power key flashes once if the 

setting is activated).

To deactivate the punch through volume setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "VOL -" key.
3. Press desired Device Mode Key of the device you want to change the 

volume on.

4. Release "VOL -" (the indicator light under the power key flashes twice if the 

setting is deactivated).

F820-8362-0001

6

380 x 180mm (fold to 95 x 180mm)

7

Macro Power allows you to turn two of your A/V equipment on/off 
simultaneously.

To activate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "    " key.
3. Press desired Device Mode Key (e.g. STB).
4. Release "    " (the indicator 

flashes once if the 

setting is activated).

To deactivate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "    " key.
3. Press desired Device Mode Key (e.g. STB).
4. Release "    " (the indicator 

flashes twice if the 

setting is deactivated).

1. Do not expose your URC to dust, strong sunlight, humidity, high 

temperatures or mechanical shocks.

2. Do not use old and new batteries together as old batteries tend to leak.
3. Do not use corrosive or abrasive cleansers on your URC.
4. Keep the unit dust free by wiping it with a soft, dry cloth.
5. Do not disassemble your URC, it contains no user-serviceable parts.

Q. My URC does not work at all!
A. Check your A/V device, if the device's main switch is turned off, your URC 

cannot operate your device.

A. Check whether your batteries are inserted properly and are in the correct 

+/- position.

A. Check whether you have pressed the corresponding device mode key for 

your device.

A. If the batteries are low, replace the batteries.

Q. If several Device Codes are listed under the brand of my A/V device, how 

can I select the correct Device Code?

A. To seek the correct Device Code for your A/V device, test the codes one by 

one until most keys work properly.

Q. My A/V equipment responds only to some of the commands.
A. You have set a code for which only some commands work properly but 

some do not. Try other codes until most keys work properly.

light under the power key 

light under the power key