Manualsbrain.com
  1. Manuali
  2. Marche
  3. Korg
  4. TONEWORKS AX5B
  5. Manuale Utente

Korg TONEWORKS AX5B Manuale Utente

Scarica
Pagina di 4
AX3-Series EasyStart 
 
3  
 
 
 
Note: 
The effect chart printed on the face of your AX5G and B will be indispensable in locating and identifying the various 
available effect choices. There is also a more detailed chart in the back of the included manual. 
 
3. 
Use the Value Knob to adjust the FX’s main parameter.  
4. 
 To fine tune the sub-parameters (not applicable to LEVEL, NR, CAB, MIC & BODY, TONE, and NOTCH), set the Function Knob to the 
corresponding effect type “PARAM” position (the next position moving clockwise on the knob). Choose the desired parameter with the 
Write (“UP”) & Cancel (“DOWN”) Buttons and use the Value Knob to adjust the parameter value. 
 
 
Note: 
 A list of effect parameters can be found in the aforementioned effect chart in the rear of the manual. This will be 
very helpful in determining which parameter is being adjusted. 
 
Tip: 
 The Original Value Indicator (small dot in the lower right corner of the Program/Value Display) can be used to 
indicate the saved effect parameter settings of the currently selected program. Simply put, when the Original Value 
Indicator is lit, the previously saved effect parameter setting has been selected. 
 
 
 
E
E
x
x
a
a
m
m
p
p
l
l
e
e
 
 
(
(
a
a
l
l
l
l
 
 
A
A
X
X
5
5
 
 
m
m
o
o
d
d
e
e
l
l
s
s
)
)
 
 
1. 
Select MOD with the Function Knob.  
2. 
Use the Write (“UP”) & Cancel (“DOWN”) Buttons to select “F2” (CL Flange). Then use the Value Knob to adjust the CL Flange 
effect’s Main parameter (SPEED). 
3. 
Turn the Function Knob clockwise one position to PARAM. Use the Write (“UP”) & Cancel (“DOWN”) Buttons to select “P2” 
(DEPTH). Use the Value Knob to adjust the level of the DEPTH parameter. 
 
Note: 
 In this mode, if you press the Program Up (Value) switch, the current parameter value will be displayed. If you 
press the Program Down (Type/Param) switch, it will display to the currently selected FX type/parameter.   
 
 
 
S
S
a
a
v
v
i
i
n
n
g
g
 
 
a
a
 
 
P
P
r
r
o
o
g
g
r
r
a
a
m
m
 
 
You’ve tweaked and turned some knobs, and you like the changes that you’ve made – now to save your program: 
 
1. 
Set the Function Knob to the “WRITE” position, and press WRITE (“UP”) Button. A User program number will blink in the 
Program/Value Display. 
2. 
Use the Program Up and Down Switches or Value Knob to select the destination program number (1 - 40) 
3. 
Press the WRITE (“UP”) Button once again, and your program will be stored in the specified location (“CP” will display briefly indicating 
the process is complete). 
 
 
 
 
A
A
m
m
p
p
/
/
L
L
i
i
n
n
e
e
 
 
S
S
e
e
t
t
t
t
i
i
n
n
g
g
 
 
(
(
A
A
X
X
5
5
G
G
 
 
o
o
n
n
l
l
y
y
)
)
 
 
The AX5G’s output may be optimized to suit specific monitoring sources via the Amp/Line setting. Amp/Line settings can be 
made under the P5 parameter of the Drive/Amp (Note; the amp line setting is only applicable to Amp models {i.e. A0, A1, 
A2, A3, etc.} and will not be found on Drive models {i.e. D0, D1, D2, D3, etc.}). Select “A1” if you connect the AX5’s output 
to the input of a clean-sounding open back combo. Select “A2” if you connect the AX5’s output to the input of an open back 
combo with stronger mid-range content. Select “A3” if you connect the AX5’s output into a sealed back cabinet such as an 
amp stack. Select “Ln” if you connect the AX5’s output into a line input such as a mixer, recorder, headphones or any other 
full range monitoring source.