Leibherr USA Refrigerators and freezers for integrated use, door-on-door HRB 1110 HF 851 Manuale Utente

u

Position  the  upper  cover

Fig.  31  (39)

  and  snap  into

place.

u

Place  the  lateral  cover

Fig. 31 (40)

 in position, slide

to the limit and then press

until  it  snaps  audibly  into

place.

u

Attach covers

 Fig. 31 (41)

 to

the  side  and  then  draw

them  forward  with  a

screwdriver,  so  that  they

snap properly into place.

Fig. 31 

u

Position the covers

 Fig. 11 (6,7,42)

 and snap them into

place.

u

Position  the  covers

  Fig.  11  (4,6,7)

  and  snap  them  into

place.

Check the following points to make sure the appliance is

installed  correctly.  Otherwise,  icing  up,  the  formation  of

condensate, and malfunctions can occur.
w

The door must close properly.

w

The unit door must not touch the body of the unit.

w

The seal on the upper corner on the handle side must be

fitted securely. To verify this, darken the room, place a

flashlight in top part of the appliance, and close the door.

If you see light shining out, check the assembly.

The water filter guarantees optimal water quality and should

be installed the first time you use the appliance.
Alternatively, the appliance can also be operated without

the water filter.

Flow rate

0.5 gpm (1.89 lpm)

Water connection Public or private source
Water pressure

40 psi - 90 psi ( 2.8 bar - 6.2 bar/ 0.28 MPa

- 0.62 MPa )

Water temperature 33 °F - 100 °F ( 0.6 °C - 37 °C )
Capacity

500 gal. (1893 l)

Consuming contaminants can be harmful to your health!

u

If  there  is  a  chance  the  water  may  contain  harmful

bacteria or if the water quality is unknown, do not use this

system  without  appropriate  disinfection  measures

upstream or downstream of the system.

Leakage water may damage the system!

u

Do  not  install  this  system  on  hot  water  lines.  The

maximum  operating  temperature  of  the  water  in  this

system is 100 °F (37.7 °C).

u

This system MUST be installed and used in compliance

with federal and local installation regulations.

u

Do not install under water hammer conditions. A water

hammer  arrestor  must  be  used  to  prevent  water

hammering.  If  you  are  unsure  how  to  check  these

conditions, consult a professional installer.

u

Do not install with a water pressure greater than 90 psi

(6.2 bar). If your water pressure exceeds 80 psi, install a

pressure limiting valve. If you are unsure how to check

the water pressure, consult a professional installer.

u

Protect  against  frost;  if  temperatures  below  33  °F

(0.6 °C) are expected, remove the filter.

u

When used as indicated, the disposable filter cartridges

must be replaced every 6 months or whenever you notice

a considerable decrease in the flow rate.

Make sure that the following conditions are

fulfilled:
q

The  hoses  have  been  positioned  such

that  they  can  now  be  connected  to  the

filter.

q

The  installation  position  has  been

selected  according  to  the  instructions

q

The connectors have been removed from

the hose ends.

u

Hoses have been shortened, if necessary

(cut  at  90°  angle  to  the  direction  of  the

hose).

When doing so, make sure the hoses do not become kinked

and the cross-section of the hose remains round.

u

On  the  thin  hose,  measure  the

insertion depth (E) of 21/32 '' (17 mm)

and mark it.

u

On  the  thick  hose,  measure  the

insertion depth (E) of 25/32 '' (20 mm)

and mark it.

u

Insert 

the 

hoses

Fig. 32 (1)

all the way into

the  water  filter  module

(i.e., up the the mark you

made),  past  the  point  of

resistance.

Fig. 32