Kingston Technology ValueRAM memory 6 GB ( 3 x 2 GB ) DIMM 240-pin DDR3 KVR1066D3E7SK3/6GI Scheda Tecnica
Codici prodotto
KVR1066D3E7SK3/6GI
Memory Module Specifications
KVR1066D3E7SK3/6GI
6GB (2GB 256M x 72-Bit x 3 pcs.) PC3-8500
CL7 ECC 240-Pin DIMM Kit
CL7 ECC 240-Pin DIMM Kit
Kingston.com
Document No. VALUERAM0794-001.A00 05/20/09 Page 1
DESCRIPTION
ValueRAM’s KVR1066D3E7SK3/6GI is a kit of two 256M x 72-bit
2GB (2048MB) DDR3-1066 CL7 SDRAM (Synchronous DRAM)
ECC, Intel
2GB (2048MB) DDR3-1066 CL7 SDRAM (Synchronous DRAM)
ECC, Intel
®
Compatibility Tested, memory modules, based on
eighteen 128M x 8-bit DDR3-1066 FBGA components. Total kit
capacity is 6GB (6144MB). Each module’s SPD is programmed to
JEDEC standard latency 1066Mhz timing of 7-7-7 at 1.5V. Each
240-pin DIMM uses gold contact fingers and requires +1.5V. The
electrical and mechanical specifications are as follows:
capacity is 6GB (6144MB). Each module’s SPD is programmed to
JEDEC standard latency 1066Mhz timing of 7-7-7 at 1.5V. Each
240-pin DIMM uses gold contact fingers and requires +1.5V. The
electrical and mechanical specifications are as follows:
FEATURES
• JEDEC standard 1.5V ± 0.075V Power Supply
• VDDQ = 1.5V ± 0.075V
• 533MHz fCK for 1066Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 5,6,7,8,9,10
• Posted CAS
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 6(DDR3-1066)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with start-
• VDDQ = 1.5V ± 0.075V
• 533MHz fCK for 1066Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 5,6,7,8,9,10
• Posted CAS
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 6(DDR3-1066)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with start-
ing address “000” only), 4 with tCCD = 4 which does not allow
seamless read or write [either on the fly using A12 or MRS]
seamless read or write [either on the fly using A12 or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ pin
• Internal(self) calibration : Internal self calibration through ZQ pin
(RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us
at 85°C < TCASE ≤ 95°C
• Asynchronous Reset
• 1066Mbps CL7 doesn’t have backward compatibility with
• 1066Mbps CL7 doesn’t have backward compatibility with
800Mbps CL5
• PCB : Height 1.180” (30.00mm), double sided component
SPECIFICATIONS
CL(IDD)
7 cycles
Row Cycle Time (tRCmin)
50.63ns (min.)
Refresh to Active/Refresh
110ns
Command Time (tRFCmin)
Row Active Time (tRASmin)
37.5ns (min.)
Power
1.890 W (operating per module)
UL Rating
94 V - 0
Operating Temperature
0° C to 85° C
Storage Temperature
-55° C to +100° C
Continued >>