Dacor ER30DSRCLP Utilizzo E Cura
28
Replacing the Light Bulbs
WARNING
• To prevent electrical shock and/or personal injury, make
certain that the oven and light bulb(s) are cool and that
power to the oven has been turned off at the main power
supply before replacing the light bulb(s).
• Always make sure the lens covers are in place when using
the oven. The lens covers protect the bulbs from breakage.
• Replacing the lens cover without lining up the cutout with
the light socket will damage the light fixture.
• Do not use a screwdriver to remove the lens cover.
Light bulb replacement is considered to be a homeowner
maintenance operation. If the lights do not work, before
replacing them, please consult the Problem Solution
Guide on page 29.
IMPORTANT: Do not touch the replacement halogen light
IMPORTANT: Do not touch the replacement halogen light
bulb with your fingers. Halogen bulbs are sensitive to the
oils from your hand. The oils from your hand will stick to
the bulb and may cause it to burn out faster than normal.
To replace the light bulbs, follow these steps:
1. Replace the light bulb only with Dacor part number
100429. See the facing page for ordering information.
2. Turn off power to the range at the circuit breaker
panel or fuse box.
3. Hold your hand under the lens for support and gently
pry it loose using a spatula or table knife. Pull the lens
cover straight out.
4. Grasp the old bulb and pull it straight out of the
socket.
5. Using a glove, insert the new bulb into the socket.
6. As you reinstall the lens cover, line up the cutout on
6. As you reinstall the lens cover, line up the cutout on
the inside rim with the light socket. Gently press it
into its original position.
7. Turn the power to the range back on. Reset the clock
(see page 9).
Care and Cleaning
Light fixture
in oven wall
Light
socket
Lens
Lens cutout
Light bulb
Adjusting the Oven Temperature Control
Even though your oven is adjusted at the factory to cook
at the temperature shown on the display, it may cook
faster or slower than your old oven.
WARNING
Do not adjust the probe or self clean offset temperatures. The
offset for the probe and self clean offsets must remain at 0 for
proper and/or safe operation.
IMPORTANT: Do not measure the temperature inside the
oven with a thermometer. Opening the door will cause an
incorrect reading. Also, the temperature inside the oven
will vary as the elements cycle on and off.
If you are not satisfied with the results from your oven,
If you are not satisfied with the results from your oven,
you can adjust the temperature offset as follows:
1. With the oven off, press and hold the
1. With the oven off, press and hold the
BAKE key for about six seconds.
The current offset temperature will appear
The current offset temperature will appear
on the display, for example “0,” if you have not
adjusted the temperature before.
2. Enter the new offset temperature.
Within six seconds, enter the amount you
want to increase or decrease the tem-
perature on the number keypad. To enter
a minus sign, press the SELF CLEAN key after the
number(s). A minus sign means that the oven will be
cooler by the amount shown. When there is no sign
in front of the number, the oven will be hotter by the
amount shown. You may enter a number between
35°F or -35°F (19°C or -19°C).
3. Press CANCEL/SECURE to save the
changes.
IMPORTANT: If you do not press
IMPORTANT: If you do not press
CANCEL/SECURE, your changes will not be saved.
Determining the Amount of Adjustment Needed
See the chart below for suggestions on the amount you
need to adjust the oven for the results you want. The
amount of food browning, moistness and rise time during
baking will suggest the amount of adjustment you need.
To Cook Food...
Change Temperature By...
A little bit more...
+10°F (+6°C)
Moderately more...
+20°F (+11°C)
A lot more...
+30°F (+17°C)
A little bit less...
-10°F (-6°C)
Moderately less...
-20°F (-11°C)
A lot less...
-30°F (-17°C)