Lynx L42PSR2 Manuale Proprietario
37
pull off the control knob.
while holding the valve
while holding the valve
shaft with pliers, insert a
hile holding the valve
hile holding the valve
thin flat-blade screwdriver
shaft with pliers, insert a
shaft with pliers, insert a
into the shaft and, while
watching the flame, adjust
it to a minimum stable
setting.
brass burner
flame/aIr sHutter
adjustment
the amount of air that enters
a burner is controlled by the
air shutter
.
each grill burner is tested and
adjusted at the factory prior to
ach grill burner is tested and
ach grill burner is tested and
shipment. However, fluctua
adjusted at the factory prior to
adjusted at the factory prior to
-
tions in gas pressure, gas con-
version and even in the quality
tions in gas pressure, gas con-
tions in gas pressure, gas con-
of the gas itself may make it
version and even in the quality
version and even in the quality
necessary to adjust the burner.
The flames of the main brass
The flames of the main brass
burners should be visually
checked
stable with slight yellow tips.
the bright-blue core should
stable with slight yellow tips.
stable with slight yellow tips.
be about 3/8 inch high with a
total flame height of about 1
be about 3/8 inch high with a
be about 3/8 inch high with a
ting burner adjustment.
1/2 inches.
The flames should burn
The flames should burn
quietly. (no “torch” sounds)
and they should not “lift” up
quietly. (no “torch” sounds)
quietly. (no “torch” sounds)
from the burner.
and they should not “lift” up
and they should not “lift” up
If your flames do not match
those indicated in the photo,
ensure that the air shutter and
those indicated in the photo,
those indicated in the photo,
burner ports are free and clear
of dirt, debris, or spider webs.
burner ports are free and clear
burner ports are free and clear
f clear, then adjust the air
of dirt, debris, or spider webs.
of dirt, debris, or spider webs.
shutter.
t is locked in place by a screw
which must be loosened
t is locked in place by a screw
t is locked in place by a screw
before adjusting. once
adjusted retighten the screw.
to
tt adjust:
Remove the racks and
briquette trays.
lift out the burner, loosen
lift out the burner, loosen
the set screw and then put
the burner back in place
the set screw and then put
the set screw and then put
and light it.
the burner back in place
the burner back in place
If the flame is excessively
yellow, indicating insuf-
If the flame is excessively
If the flame is excessively
ficient air, CAREFULLY turn
yellow
yellow, indicating insuf-
, indicating insuf-
the air shutter counter-
clockwise to allow more air
to the burner.
If the flame is noisy (sounds
If the flame is noisy (sounds
like a torch) and tends to
danger!
Be extremely careful
around hot Burners
and other grill parts.
lift away from the burner,
indicating too much
air, turn the air shutter
clockwise.
after the burner cools
after the burner cools
down, remove it, tighten
the air shutter set screw
and reinstall the burner,
briquette trays and grill
racks.
briquette trays and grill
briquette trays and grill
one last tHIng:
finally, before leaving, check
all the burners for proper
inally, before leaving, check
inally, before leaving, check
operation. make sure the
ners for proper
ners for proper
control knobs turn freely and
operation.
operation.
completely through their full
control knobs turn freely and
control knobs turn freely and
range.
Important:
mportant
mportant
make sure the owner knows
where the main gas supply
shut off valve is located.
where the main gas supply
where the main gas supply
finally, for safety and for
proper use & care, you
must leave this manual with
the owner. make sure you
advise them to keep it for
ake sure you
ake sure you
future reference.
for technical assistance call:
lynx
lynx
ll
technical
tt
support
888-289-5969