Maytag MFC2062DEM Utilizzo E Cura

1. Remove the freezer handle assembly as shown in Graphic 4. 

Keep all parts together. 

2. Remove door stop. Move to opposite side of freezer door as 

shown in Graphic 3.

3. Attach handle to opposite side of freezer door.
4. Tighten all screws. Set the door aside.
5. Remove the base grille by grasping the grille firmly with both 

hands and pulling it toward you. 
NOTE: Place a shim under the bottom front edge of the 
refrigerator cabinet to take the weight off the roller brackets.

6. Remove the screws from both roller brackets. See Graphic 6. 
7. Remove the hinge plate located behind the roller bracket and 

move it to the opposite side of the refrigerator. Move the hinge 
pin and shim to the outside hole on the hinge plate. See 
Graphic 6. 

NOTE: Graphics may be reversed if door swing is reversed.
Freezer drawer models

1. Replace the parts for the bottom hinge as shown. Tighten 

screws.
NOTE: Provide additional support for the door while the 
hinges are being moved. Do not depend on the door gasket 
magnets to hold the door in place while you are working.

2. Assemble the parts for the top hinge as shown in Top Hinge 

graphic. Do not tighten screws completely. 

3. Adjust the door so that the bottom of the refrigerator door is 

aligned with the top of the freezer drawer. Tighten all screws.

1. Make sure the hinge plate is securely fastened behind the 

roller bracket and that the hinge pin is inserted into the outside 
hole. Fully tighten all roller bracket screws. See Graphic 6. 

2. Remove the shim that you placed under the front edge of the 

refrigerator cabinet. Replace the freezer door. 
NOTE: Provide additional support for the door while the 
hinges are being moved. Do not depend on the door gasket 
magnets to hold the door in place while you are working.

3. Assemble the parts for the center hinge as shown in the 

Center Hinge graphic, and tighten all the screws. Replace the 
refrigerator door. 

4. Assemble the parts for the top hinge as shown in the Top 

Hinge graphic. Do not tighten the screws completely. 

5. Adjust the doors so that the bottom of the refrigerator door is 

aligned with the top of the freezer door. Tighten all screws. 

1. Assemble the parts for the top hinges as shown in Top Hinge 

graphic. Do not tighten the screws completely.

2. Replace the parts for the bottom hinges as shown in Bottom 

Hinge graphic. Tighten screws. Replace the refrigerator doors.
NOTE: Provide additional support for the refrigerator doors 
while the hinges are being moved. Do not depend on the door 
gasket magnets to hold the doors in place while you are 
working.

3. Align each door so that the bottom of the refrigerator door 

aligns evenly with the top of the freezer drawer. Tighten all 
screws.

4. Reconnect the wiring plug on top of the left-hand side 

refrigerator door.

5. Replace the top hinge covers.

■

Two people may be required to remove and replace the freezer 
drawer.

■

All graphics are included later in this section after “Final 
Steps.”

1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer glides to the 

drawer front. See Drawer Front Removal graphic. 
NOTE: Loosen screws three to four turns. Keep the screws in 
the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front 

Removal graphic. 

1. Slide the drawer glides out of the freezer compartment. Insert 

the screws in the top of the drawer front into the slots in the 
drawer brackets. See Drawer Front Replacement graphic. 

2. Pull the drawer brackets toward you to insert the two screws 

in the bottom of the drawer front into the brackets. See 
Drawer Front Replacement graphic. 

3. Completely tighten the four screws. 

1. Check all holes to make sure that hole plugs and screws are in 

place. Reinstall top hinge cover as shown in Top Hinge 
graphic.

2. Replace the base grille.

3. Plug into a grounded 3 prong outlet. 
4. Return all removable door parts to door and food to 

refrigerator.