Faber TEND30SS300 Foglio Delle Specifiche
Dimensional Diagrams
36” Ducted
30” Ducted
For ducted installations
the chimneys are adjustable and
designed to meet varying ceiling
heights between 7’ 9 2/16” and 9’
11 2/16” depending on the distance
between the bottom of the hood
and the cooktop (distance x in the
ducted diagram).
designed to meet varying ceiling
heights between 7’ 9 2/16” and 9’
11 2/16” depending on the distance
between the bottom of the hood
and the cooktop (distance x in the
ducted diagram).
For shorter ceilings, have
the chimney cover(s) cut at a sheet
metal shop. For higher ceiling
installations, the High Ceiling
Chimney Kit includes a new 39”
upper chimney which would replace
the 21 10/16” upper chimney that
came with the hood.
metal shop. For higher ceiling
installations, the High Ceiling
Chimney Kit includes a new 39”
upper chimney which would replace
the 21 10/16” upper chimney that
came with the hood.
Note: If 24” or 30” High Backsplash is being installed, the distance between the bottom of the hood and the cooktop (distance x in diagram) is equal
to the height of the Backsplash.
Ducted
* it is highly recommended that
professional style cooking always be
vented to the outside.
professional style cooking always be
vented to the outside.
WARNING!
Product specifications are subject to change without notification. Consult the installation instructions before you begin installing this rangehood.
Pre-Planning Your Installation -
Important: Consult the installation
instructions before you begin installing this rangehood.
Ductless Installations*
For installations where ductwork is impos-
sible or highly impractical, a Ductless
Conversion Kit is available. A charcoal
filter, which attaches under the blower
assembly, absorbs smoke and odors. A
ductless diverter assembly directs the air
out to a lower chimney with vent grates cut
into the sides.
sible or highly impractical, a Ductless
Conversion Kit is available. A charcoal
filter, which attaches under the blower
assembly, absorbs smoke and odors. A
ductless diverter assembly directs the air
out to a lower chimney with vent grates cut
into the sides.
Make your ductrun as straight and short as possible. The ductrun should not exceed
35 equivalent feet if ducted with the required minimum of 6” round duct. Count 45º
angles as 3 feet, 90º elbows as 5 feet, and 90º flat elbows as 12 feet.
For best results, use no more than three 90° elbows. Make sure that there is a
minimum of 24” of straight duct between elbows if more than one is used. Do
not install two elbows together. If you must elbow right away, do it as far away
from the hood’s exhaust opening as possible.
35 equivalent feet if ducted with the required minimum of 6” round duct. Count 45º
angles as 3 feet, 90º elbows as 5 feet, and 90º flat elbows as 12 feet.
For best results, use no more than three 90° elbows. Make sure that there is a
minimum of 24” of straight duct between elbows if more than one is used. Do
not install two elbows together. If you must elbow right away, do it as far away
from the hood’s exhaust opening as possible.
Pre-Planning Your Installation -
Important: Consult the installation instructions before you begin installing this rangehood.
Rev. 07/11
1” min
21 10/16
”
max
22 1/16”
9
7/16”
36”
x
also consult cooktop
manufacturer's recommendation
upper
chimney
lower
chimney
canopy
x = distance from hood to cooktop
(varies depending on installation)
min - 24”, suggested max - 30”
cabinet base
19
”
min & max ceiling height examples
x = 30"
min
8'
3 2/16
max
9'
11 2/16"
x = 28"
min
8'
1 2/16"
max
9'
9 2/16"
x = 26"
min
7'
11 2/16"
max
9'
7 2/16"
x = 24"
min
7'
9 2/16"
max
9'
5 2/16"