Maytag MFX2876DRH Scheda Tecnica

A shallow storage compartment with glass lids which slide from 
side to side is located below and in front of the crisper drawers. 

NOTE: This compartment is not temperature or humidity 
controlled, so it is not recommended for storing leafy vegetables. 

1. Remove all three crisper drawers.

2. Hold the upper sliding lid near the trim and lift up to remove. 

Remove the lower lid.

3. Grasp the front of the bin with both hands, and lift up on the 

front to remove. 

1. Slightly tilt the rear of the bin upward.

2. Align the center rib and tabs on the EasySlide bin with the 

ribs and slots in the cabinet.

3. Lower the bin into place.  

1. Grasp the handle at the bottom of the drawer and slide the 

drawer straight out to the stop. Lift the drawer off the bottom 
guide.

2. Replace the drawer by placing it on the bottom drawer guide 

and pushing it past the drawer stop into position. 

1. Remove crisper drawers.

2. Holding the glass insert firmly with one hand, press up in 

center of glass insert until it rises above the plastic frame. 
Gently slide the glass insert forward to remove.

3. Lift the cover frame up and remove it.

1. Fit back of cover frame into supports on side walls of the 

refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into 

place.

3. Replace crisper drawers.

■

Allow 3 hours for the refrigerator to cool down and chill water.

■

Allow 24 hours to produce the first batch of ice. Discard the 
first three batches of ice produced. Allow 2 to 3 days for the 
storage bin to fill completely following installation.

■

The dispensing system will not operate when either 
refrigerator door or the freezer drawer is open.

Air in the water dispensing system can cause the water dispenser 
to drip. After connecting the refrigerator to a water source or 
replacing the water filter, flush the water system. 

Flushing the water dispensing system, forces air from the water 
line and filter and prepares the water filter for use. Additional 
flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of 
the dispenser.

1. Using a sturdy container, depress and hold the water 

dispenser pad for 5 seconds.

2. Release the dispenser pad for 5 seconds. Repeat steps 1 and 

2 until water begins to flow. 

3. Once water begins to flow, continue depressing and releasing 

the dispenser pad (5 seconds on, 5 seconds off) until a total 
of 3 gal. (12 L) has been dispensed.

IMPORTANT: 

■

Dispense at least 1 qt (1 L) of water every week to maintain a 
fresh supply.

■

If the flow of water from the dispenser decreases, it could be 
caused by low water pressure. 

■

With the water filter removed, dispense 1 cup of water. If 
1 cup of water is dispensed in 8 seconds or less, the 
water pressure to the refrigerator meets the minimum 
requirement.

■

If it takes longer than 8 seconds to dispense 1 cup of 
water, the water pressure to the refrigerator is lower than 
recommended. See “Water Supply Requirements” and 
“Troubleshooting” for suggestions.

Ice dispenses from the ice maker storage bin. To turn off the ice 
maker, see “Ice Maker and Storage Bin.”

The dispenser may continue to make noise and ice may continue 
to dispense for several seconds after releasing the dispenser 
button or pad.

IMPORTANT: If the ice cubes are hollow or have an irregular 
shape, it could be because of low water pressure. See “Water 
Supply Requirements.”

Humidity causes ice to naturally clump together. Ice particles can 
build up until the ice dispenser chute becomes blocked. 

If ice is not dispensed regularly, it may be necessary to empty the 
ice storage bin and clean the ice delivery chute, the ice storage 
bin and the area beneath the storage bin every 2 weeks.

A

B