Frigidaire FFWC35F4LB Manuale Proprietario

5

The glass door can be opened from left to right and vice 

versa. Should you desire to change the opening direction, 

please follow these instructions.



All parts removed must be saved to do the 

reinstallation of the door.

Remove top cap. Remove the three screws that hold 

the upper hinge (right side) to the top of the cabinet. 

See Fig. 1. 
Carefully remove top hinge (See Fig. 1.), then lift the 

door up off of bottom hinge and place it on a padded 

surface to prevent scratching it. See Fig. 2.
Remove the three button plugs from the upper left 

corner of the cabinet and transfer them to the  holes 

on the opposite side. Be sure to press the button 

plugs firmly into the holes. See Fig. 1.
Remove three screws that hold the bottom hinge to 

lower end of cabinet. Remove the three button plugs 

from lower LH corner and transfer to holes where 

bottom hinge was just removed. See Fig. 3.
Unscrew pins from both hinges and transfer to 

threaded hole on opposite side. See Fig. 4. Re-install 

bottom hinge in LH corner of cabinet using same 

three screws removed in Step 4.
On bottom edge of door, transfer door stop bracket 

and bushing to holes on opposite side. See Fig. 6.
On top edge of door, transfer the button plugs and 

bushing to hole on opposite side. See Fig. 7.
Place bottom LH corner of door onto lower hinge, 

then install top hinge to cabinet. Make sure door 

is level and it seals properly against cabinet, then 

securely fasten three screws. See Fig. 7. Snap top 

cap back onto hinge.

 

Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart 

3) 

Step 8:Remove the screw� and the block �,then set them on the left side.(see 

chart 3) 

 

ľ

ļ

Ľ

Step 9:Change the hinge axis� from the right hole to left hole(see chart 4) 

 

 

Ŀ

Step 10:Use knife to remove the parts�,see chart 5. 

- 8 - 

Screws

Top cap

Bushing

Hinge

� Handle 

ĸ

 Wooden Shelf Made of Beech 

Ĺ

  Control Panel 

� Glass Door 
� Control Switch of Lamp 
� Adjustment Leg 

Door Reversal Instructions: 

You can reverse the door swing if you change the position of the hinge(�) ,pls 

follow the steps below:   

Step 1:Close the door and use the knife carefully to remove the parts�ǃ�(see 

chart 1) 

Step 2:Remove the hinge coverĹ(see chart 1) 

Step 3:Remove the screws by cross-screwdriverĺ(see chart 1) 

Step 4:Remove the top hingeĻ(see chart 1) 

Step 5:Remove the bolt by screwdriverļ(see chart 1) 

 

ĸ

 

ķ

Ĺ

ĺ

Ļ

ļ

Step 6:Open the door and lift it up carefully then remove it,see chart 2.   

- 7 - 

Button plugs

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the 

left and right sideˈthen assemble the parts,see chart 6. 

 

ĸ

 

ŀ

ĺ

 

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see 

chart 7. 

 

 

ŋ

 

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt� 

- 9 - 

Move pin to 

opposite hole 

(upper and 

lower hinges)

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the 

left and right sideˈthen assemble the parts,see chart 6. 

 

ĸ

 

ŀ

ĺ

 

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see 

chart 7. 

 

 

ŋ

 

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt� 

- 9 - 

Button plugs

Screws

Hinge

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the 

left and right sideˈthen assemble the parts,see chart 6. 

 

ĸ

 

ŀ

ĺ

 

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see 

chart 7. 

 

 

ŋ

 

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt� 

- 9 - 

Button plugs

Screws