Maytag MFW2055YEB Scheda Tecnica

NOTE: As air is cleared from the system, water may spurt out of 
the dispenser.

1. Using a sturdy container, depress and hold the water 

dispenser paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds. Repeat steps 1 

and 2 until water begins to flow. 

3. Once water begins to flow, continue depressing and releasing 

the dispenser pad (5 seconds on, 5 seconds off) until a total 
of 4 gal. (15 L) has been dispensed.

IMPORTANT: 

■

The dispensing system will not operate when the refrigerator 
door is open.

■

The display screen on the dispenser control panel will turn off 
automatically and enter “sleep” mode when the control 
buttons and dispenser levers have not been used for 
2 minutes or more. While in “sleep” mode, the first press of a 
control button will only reactivate the display screen, without 
changing any settings. After reactivation, changes to any 
settings can then be made. If no changes are made within 
2 minutes, the display will re-enter “sleep” mode.

1. Press a sturdy glass against the water dispenser paddle.

2. Remove the glass to stop dispensing.

When you use the dispenser, the light will automatically turn on. 
If you want the light to be on continuously, you may turn on the 
light. The light icon will illuminate when the light is on. 

ON: Press LIGHT quickly to turn on the dispenser light. 

OFF: Press LIGHT quickly to turn off the dispenser light.

■

If you unintentionally press and hold the LIGHT button for 
3 seconds or longer, you will turn on the Moisture control 
feature. If this happens, press and hold LIGHT for 3 seconds 
again to turn off the Moisture control feature.

■

The dispenser lights are LEDs that cannot be changed. If it 
appears that your dispenser lights are not working, see 
“Troubleshooting” for more information.

Dispenser Lock 

The dispenser can be turned off for easy cleaning or to avoid 
unintentional dispensing by small children and pets. 

NOTE: The lock feature does not shut off power to the 
refrigerator, to the ice maker, or to the dispenser light. It simply 
deactivates the controls and dispenser levers. To turn off the ice 
maker, see “Ice Maker.”

■

Press and hold SPEEDCOOL for 3 seconds to lock the 
dispenser. 

■

Press and hold SPEEDCOOL for 3 seconds again to unlock 
the dispenser.

The lock icon will illuminate when the dispenser is locked. 

IMPORTANT: For models with a water filter, after connecting the 
refrigerator to a water source or replacing the water filter, fill and 
discard three full containers of ice to prepare the water filter for 
use. 

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF, lift the wire shutoff arm to the 
OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made, 
the ice cubes will fill the ice storage bin and the ice cubes will 
raise the wire shutoff arm to the OFF (arm up) position. Do not 
force the wire shutoff arm up or down.

1. Wash the ice storage bin with mild soap and warm water.

2. Slide the ice storage bin under the ice maker, and push it 

toward the back as far as it will go.

3. Lower the arm on the ice maker to the “on” position. 

NOTE: It usually takes approximately 24 hours for the ice 
maker to begin producing ice. You may notice the ice has an 
“off-taste.” If so, discard the first three batches of ice 
produced. After that the “off-taste” should be gone.

■

The ice maker should produce approximately 8 to 12 batches 
of ice in a 24-hour period. Allow 3 days to completely fill the 
ice container. 

■

To increase ice production, lower the freezer and refrigerator 
temperature. See “Using the Control(s).” Wait 24 hours 
between adjustments.