Keurig K550 Brewing System Manuale Istruttivo
3
VINEGAR
WHITE
OR
METHOD 1
Keurig
TM
Descaling Solution
Before you begin, you will need a large ceramic mug, fresh water,
Keurig
Keurig
™
Descaling Solution and access to a sink. Do not use a paper cup.
STEP 1: FIRST DESCALING SOLUTION RINSE
• Turn on your brewer.
• Pour one third (4.6 oz.) of the Keurig
• Pour one third (4.6 oz.) of the Keurig
™
Descaling Solution into the Cold
Water Reservoir, and add fresh water to the 10 oz. FILL LEVEL Indicator.
• Place a large ceramic mug on the Drip Tray Plate. Do not use a paper cup.
• Lift Handle, but do not add a K-Cup
• Lift Handle, but do not add a K-Cup
®
pack.
• After 5 seconds, lower Handle and press the BREW Button.
• Once solution is dispensed, discard hot contents into sink.
• Once solution is dispensed, discard hot contents into sink.
STEP 2: SECOND DESCALING SOLUTION RINSE
• Repeat above process up until you press the BREW Button.
• When BREW Button turns solid red, power off as it starts to dispense.
• Let the brewer stand for at least 30 minutes.
• Power on the brewer, lift and lower Handle, then press the
• When BREW Button turns solid red, power off as it starts to dispense.
• Let the brewer stand for at least 30 minutes.
• Power on the brewer, lift and lower Handle, then press the
BREW Button.
• Discard the hot contents into sink.
STEP 3: FRESH WATER RINSE
• Repeat Step 1 (three times) substituting the Descaling Solution for 10 oz. of
fresh water each time.
• You may need to perform additional Fresh Water Rinse cycles if you notice any
residual taste.
NOTE: The cleaning action of the Keurig
NOTE: The cleaning action of the Keurig
™
Descaling Solution may result in
a foam dispensed from the brewer. This is natural, as the solution is reacting
with the scale inside. For a brewer that is heavily scaled, the brewer may
not fill properly after the descaler is added. If this occurs, you may see only
a small or no output dispensed followed by the sound of air blowing out.
If this occurs:
• Turn off and unplug the brewer.
• Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse
• Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse
cycle. The brewer should begin to function normally as the solution is rinsed
out and the scale is removed. If problem persists, allow the brewer to sit
unplugged for at least 30 minutes before continuing with the rinse.
For more information on Keurig
™
Descaling Solution or to purchase please
visit
METHOD 2
White Vinegar Descaling
Before you begin, you will need a large ceramic mug, fresh water, at least
20 oz. of undiluted white vinegar and access to a sink. Do not use a paper cup.
STEP 1: FIRST VINEGAR RINSE
• Turn on your brewer.
• Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar.
• Place the ceramic mug on the Drip Tray Plate.
• Lift the Handle, but do not add a K-Cup
• Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar.
• Place the ceramic mug on the Drip Tray Plate.
• Lift the Handle, but do not add a K-Cup
®
pack.
• After 5 seconds, lower Handle.
• Press the flashing blue BREW Button. It will flash red and then turn
• Press the flashing blue BREW Button. It will flash red and then turn
solid red.
• Once the vinegar is dispensed, discard hot contents into sink.
STEP 2: SECOND VINEGAR RINSE
• Pour the remaining 10 oz. of vinegar into the Cold Water Reservoir.
• Place the ceramic mug on the Drip Tray Plate.
• Lift Handle, but do not add a K-Cup
• Place the ceramic mug on the Drip Tray Plate.
• Lift Handle, but do not add a K-Cup
®
pack.
• After 5 seconds, lower Handle.
• Press the flashing blue BREW Button. It will then flash red.
• When it turns solid red, power off as it starts to dispense.
• Allow the brewer to sit for 30 minutes.
• Power on the brewer, lift and lower Handle, then press
• Press the flashing blue BREW Button. It will then flash red.
• When it turns solid red, power off as it starts to dispense.
• Allow the brewer to sit for 30 minutes.
• Power on the brewer, lift and lower Handle, then press
the BREW Button.
• Once the vinegar is dispensed, discard hot contents into sink.
STEP 3: FRESH WATER RINSE
• Fill the Cold Water Reservoir with 10 oz. of fresh water.
• Place the ceramic mug on the Drip Tray.
• Lift Handle, but do not add a K-Cup
• Place the ceramic mug on the Drip Tray.
• Lift Handle, but do not add a K-Cup
®
pack.
• Lower Handle and continue the brewing process until the
hot water is dispensed into the mug. Discard hot contents into sink.
• Repeat this Fresh Water Rinse cycle three (3) more times to cleanse the
brewer plumbing and to remove any residual vinegar taste. The brewer
is now ready for normal use again.
K10 MINI Plus Brewer
SELECT A DIFFERENT BREWER MODEL