Hitachi SJ100 Manuale Utente

Display

Function

Standard

Setting

Set

Value

A 01

Frequency Source setting
00-Potentiometer 01-Terminal O/OI
02-Functions

F 01

A 20

A 02

Run command source setting
01-Terminal FW/RV 02-RUN key

A 03

Base frequency setting

A203

Base frequency setting (2. setting)

50.0

A 04

Maximum frequency setting

A204

Maximum frequency setting (2. setting)

50.0

A 11

External frequency setting start point

A 12

External frequency setting end point

A 13

External frequency setting start point bias (in %)

A 14

External frequency setting end point bias (in %)

100

A 15

External frequency start pattern setting
00-Per

A11

and

A13

01-0Hz

A 16

Time constant of the filter for analog inputs

A 20 –

A 35

Multispeed frequency setting

All are

0.0Hz

A 38

Jog frequency setting

1.0

A 39

Jog stop mode
00-Freerun 01-Deceleration
02-DC brake

A 41

Torque boost selection method
00-Manual 01-Automatic

A241

Torque boost selection method (2.

setting)

A 42

Value of manual torque boost setting

A242

Value of manual torque boost setting (2. setting)

A 43

Manual torque boost frequency adjustment (in %)

A243

Manual torque boost frequency adjustment (in %)
(2. setting)

10.0

A 44

V/F characteristic setting
00-Constant torque
01-Variable torque 02-SLV

A244

V/F characteristic setting (2. setting)

A 45

V-Gain setting (in %)

100

A 51

Selection of DC braking operation
00-NO 01- YES

A 52

DC braking frequency setting

0.5

A 53

DC braking waiting time setting

0.0

A 54

DC braking force setting

A 55

DC braking time setting

0.0

A 61

Frequency upper limit setting

0.0

A 62

Frequency lower limit setting

0.0

A 63,
A 65,

A 67

Jump frequency setting

0.0

A 64,
A 66,

A 68

Jump frequency width setting

0.5

A 71

Selection of PID control
00-NO 01- YES

A 72

P (proportional) gain setting

1.0

A 73

I (integral) gain setting

1.0

A 74

D (differential) gain setting

0.0

A 75

Scale conversion of PID control setting

1.00

A 76

Feedback signal location setting
00-Current 01-Voltage

A 81

Selection of AVR function
00-Available 01-Not available
02-Not available at deceleration

A 82

Selection of voltage of AVR function for the
motor

FE:230/400
FE:230/460

A 92

Second acceleration time setting

A292

Second acceleration time setting (2. setting)

15.0

A 93

Second deceleration time setting

A293

Second deceleration time setting (2. setting)

15.0

(Table to be continued on next page)

Display

Function

Standard

Setting

Set

Value

b 01

Selection of restart mode
  00-Alarm   01-0.0Hz restart
  02-Motor speed match restart
  03-Motor speed match restart /decel to stop

b 02

Allowable undervoltage power failure time setting

1.0

b 03

Retry waiting time

1.0

b 12

Level of electronic thermal setting

b212

Level of electronic thermal setting (2. setting)

Rated current

of inverter

b 13

Selection of electronic thermal characteristic
00-Reduced torque 01-Constant torque

b213

Selection of electronic thermal characteristic
(2. setting)

b 21

Selection of overload limit operation mode
00-NO 01-Accel & constant speed
02-Constant speed

b 22

Level of overload limit setting

Rated current

times 1.25

b 23

Rate of deceleration at overload restriction

1.0

b 31

Selection of software lock mode
   00-Terminal, no change
   01-Terminal, frequency change
   02-Keypad, no change
   03-Keypad, frequency change

b 81

Analog meter adjustment

b 82

Start frequency adjustment

0.5

b 83

Carrier frequency setting (kHz)

5.0

b 84

Initialization will 00-Clear trip history

01-Restore data & parameters to factory settings

b 85

Selection of initialized data

-FE:01 -FU:02

b 86

Frequency converted value setting

1.0

b 87

STOP key active in terminal mode
00-YES 01-NO

b 88

Selection of operation when FRS signal is
cancelled
00-Restart at 0 Hz 01-Restart at motor speed

b 89

Selection of contents of remote display
   01-Frequency 02-Current   03-Direction
   04-PID feedback 05-Input terminal status
   06-Output terminal status   07-Scaled frequency

b 90

Rate of use (in %) of the regenerative braking
resistor during 100 seconds
(00= braking resistor not active)

b 91

Deceleration mode selection when using the
STOP key
00-Deceleration stop
01-Free run stop (FRS)

b 92

Fan ON/OFF selection
   00-Fan is always on
   01-Fan is only on if the inverter/motor
    is running

(Continued from previous page)

Display

Function

Standard

Setting

Set

Value

A 94

Selection of method to enable second
acceleration/deceleration (acc2/dec2)
00-Terminal 2CH 01-

A 95

A 96

A294

Selection of method to enable second
acceleration/deceleration (acc2/dec2)
(2. setting)

A 95

Changed frequency from acc1 to acc2 setting

A295

Changed frequency from acc1 to acc2 setting
(2. setting)

0.0

A 96

Changed frequency from dec1 to dec2 setting

A296

Changed frequency from dec1 to dec2 setting
(2. setting)

0.0

A 97

Pattern of acceleration setting
00-Linear 01-S-curve

A 98

Pattern of deceleration setting
00-Linear 01-S-curve

Display

Function

Standard

Setting

Set

Value

C 01

Function of input terminal 1
00-FW (Forward run) 01-RV (Reverse run)
02-CF1 (Multispeed 1) 03-Multispeed 2

04-Multispd. 3 05-Multispd. 4 06-JG (Jogging)
07-DB (Ext. DC braking) 08-SET (use 2. setting)
09-2CH (2. stage accel/decel) 11-FRS (Free run
mode) 12-EXT (Extern. trip) 13-USP-function
15-SFT (Software lock) 16-AT (Analog input
type) 18-RS (Reset) 19-PTC (only for termi-

nal 5) 27-UP (remote control acceleration)
28-DWN (remote control deceleration)

C 02

Function of input terminal 2 (See

)

C 03

Function of input terminal 3 (See

)

-FE:02 -FU:16

C 04

Function of input terminal 4 (See

)

-FE:03 -FU:13

C 05

Function of input terminal 5 (See

)

-FE:18 -FU:09

C 06

Function of input terminal 6 (See

)

-FE:09 -FU:18

C 11 –

C 16

Polarity input of terminal 1-6
00-Normally open 01-Normally closed

00 /

C 14

only

-FE:00 -FU:01

C 21

Function of output terminal 11
00-RUN-signal 01-FA1 (frequency constant)

02-FA2 (Frequency at set point) 03-OL (Over-

load) 04-OD (PID deviating) 05-AL (Alarm)

C 22

Function of output terminal 12 (See

)

C 23

Function of FM terminal 00-Analog frequency
01-Analog current 02-Digital frequency

C 24

Function of alarm terminal (See

)

C 31

Polarity of terminal 11
00-Normally open 01-Normally closed

C 32

Polarity of terminal 12 (See

)

C 33

Polarity of terminal AL0/AL1
00-Normally open 01-Normally closed

C 41

Level of overload signal setting

Rated current

C 42

Arrival frequency setting for acceleration

0.0

C 43

Arrival frequency setting for deceleration

0.0

C 44

Level of PID deviation signal setting

3.0

C 81

Frequency command adjustment (terminal O)

C 82

Frequency command adjustment (terminal OI)

C 91 –

C 95

For further use, do not change.

Display

Function

Standard

Setting

Set

Value

H 01

Autotuning mode:

00-Autotuning off

01-Autotuning on

02-Autotuning/static

H 02

Motor data: 00-Standard Hitachi 01-Auto

H202

Motor data (2.

setting)

H 03

Motor capacity

H203

Motor capacity (2.

setting)

Depending

on model

H 04

Number of motor poles

H204

Number of motor poles (2. setting)

H 05

Motor constant Kp

H205

Motor constant Kp (2. setting)

H 06

Motor stabilization constant

H206

Motor stabilization constant. (2.

setting)

100

H 20

Motor constant R1

H220

Motor constant R1 (2. setting)

H 21

Motor constant R2

H221

Motor constant R2 (2. setting)

H 22

Motor constant L

H222

Motor constant L (2. setting)

H 23

Motor constant Io

H223

Motor constant Io (2. setting)

H 24

Motor constant J

H224

Motor constant J (2. setting)

H 30

Motor constant R1 Autotuning

H230

Motor constant R1 Autotuning (2. setting)

H 31

Motor constant R2 Autotuning

H231

Motor constant R2 Autotuning (2. setting)

H 32

Motor constant L Autotuning

H232

Motor constant L Autotuning (2. setting)

H 33

Motor constant Io Autotuning

H233

Motor constant Io Autotuning (2. setting)

H 34

Motor constant J Autotuning

H234

Motor constant J Autotuning (2. setting)

Depending

on model

These

para-

meters

must not

changed!