U-Line 2175BEVOL Manuale Utente
2175BEVS, 2175BEVOL
7
Figure 2
IMPORTANT
IMPORTANT
Proper air flow (Figure 2) is required for your unit to
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.
Initial Startup
All U-Line units are shipped with controls that are preset.
No initial adjustments are required.
No initial adjustments are required.
IMPORTANT
IMPORTANT
U-Line recommends the unit be allowed to run
overnight prior to loading with product.
overnight prior to loading with product.
Figure 3
To turn the unit on or off, touch and hold the POWER icon
(Figure 3, 1) on the display panel for approximately 10
seconds until the °F symbol flashes and release.
(Figure 3, 1) on the display panel for approximately 10
seconds until the °F symbol flashes and release.
• A small LED above the icon will illuminate to confirm
the touch of any controller icon.
• The display (Figure 3, 3) will show the unit set-point
temperature when the unit is on and will show OFF
when the unit is off.
when the unit is off.
• Turning the unit off will override any other control
function.
Interior Lighting
The interior of the cabinet can be illuminated whenever
the door is opened (default mode), illuminated for a four-
hour period, or remained darkened (blackout/Sabbath
mode [not Star K certified]).
the door is opened (default mode), illuminated for a four-
hour period, or remained darkened (blackout/Sabbath
mode [not Star K certified]).
The LIGHT icon (Figure 3, 5) on the control panel is used
to change the lighting functions.
to change the lighting functions.
To illuminate the interior of the cabinet for a four-hour
period:
period:
1. Touch and release the LIGHT icon (Figure 3, 5) to
switch from door-operated lighting control to
continuous lighting (the °F symbol will flash briefly
after the LIGHT icon is pressed).
continuous lighting (the °F symbol will flash briefly
after the LIGHT icon is pressed).
2. To return to door-operated lighting control before the
four-hour period is up, repeat Step 1.
To turn the lights and display OFF (blackout/Sabbath
mode [not Star K certified]):
mode [not Star K certified]):
1. Touch and hold the LIGHT icon (Figure 3, 5) for ten
seconds and release (the °F symbol will flash briefly at
the end of the five second period).
the end of the five second period).
2. The interior light and control display (Figure 3, 3) will
go dark.
NOTE: Although the display will not be visible, the
temperature controls in the unit remain active, and the
interior temperature will be maintained.
temperature controls in the unit remain active, and the
interior temperature will be maintained.
3. To exit the blackout/Sabbath mode (not Star K
certified), repeat Step 1.
Electronic Control Panel
Your Beverage Center has been designed to provide two
temperature zones within the cabinet so the specific
storage requirements of your beverages can be satisfied.
temperature zones within the cabinet so the specific
storage requirements of your beverages can be satisfied.
Figure 4
The electronic control with digital display (Figure 4) is
configured to show a single temperature continuously.
This set-point temperature is a base number used by the
controller to maintain the temperature zones in your unit.
The factory default set-point temperature is 38°F. This set-
point temperature is used as a gauge if further
temperature adjustments are required.
configured to show a single temperature continuously.
This set-point temperature is a base number used by the
controller to maintain the temperature zones in your unit.
The factory default set-point temperature is 38°F. This set-
point temperature is used as a gauge if further
temperature adjustments are required.
5 Operation
ULIN_0080_A
1
2
3
5
4
ULIN_0184a_A
1
2
3
5
4
ULIN_0184a_A
ULIN_016357_30172.fm Page 7 Friday, February 2, 2007 11:45 AM