U-Line U-2275ZWCOL-00 Manuale Utente
u-line.com
3
Air Flow
NOTICE
The unit requires proper air flow to perform at its highest
efficiency. Do not block the front grille or internal fans at
any time, or the unit will not perform as expected. Do not
install the unit behind a door.
efficiency. Do not block the front grille or internal fans at
any time, or the unit will not perform as expected. Do not
install the unit behind a door.
Initial Startup
All U-Line controls are preset at the factory. Initial startup requires
no adjustments.
no adjustments.
NOTICE
U-Line recommends allowing the unit to run overnight
before loading refrigerator or freezer with product.
before loading refrigerator or freezer with product.
To turn the unit on or off, press and hold the POWER icon (1) for
approximately five seconds and release. The display will show the
unit set-point temperature when turned on and display OFF when
the unit is off.
approximately five seconds and release. The display will show the
unit set-point temperature when turned on and display OFF when
the unit is off.
Electronic Control Panel
Digital Display. Dual Zone Wine Captain Models provide two
controlled temperature zones to satisfy the specific storage
requirements of your finest wines.
controlled temperature zones to satisfy the specific storage
requirements of your finest wines.
The dual electronic displays are configured to display current
temperature set points for each zone. The top zone is displayed on
the upper (3) display while the lower zone set point is shown on
the lower (6) display. This set point is a base number used by the
controller to maintain the multiple temperature zones in the unit.
The factory default set-point for Wine Captain models is 50°F. The
set-point temperature is a gauge for further temperature
adjustments.
temperature set points for each zone. The top zone is displayed on
the upper (3) display while the lower zone set point is shown on
the lower (6) display. This set point is a base number used by the
controller to maintain the multiple temperature zones in the unit.
The factory default set-point for Wine Captain models is 50°F. The
set-point temperature is a gauge for further temperature
adjustments.
Dual Temperature Zones
To adjust the set point temperature:
NOTICE
Adjust the set-point temperature in single increments and
wait 24 hours for the temperature to stabilize.
wait 24 hours for the temperature to stabilize.
Your unit has been designed to provide two temperature zones
(upper and lower) in the cabinet.
(upper and lower) in the cabinet.
1. Touch and release Warmer (2) to put the controller in the SET
TEMPERATURE mode. The top of the F in “°F” will begin to
flash. This will allow you to adjust the temperature of the top
zone. After 10 seconds of inactivity, the bottom bar of the F in
“°F” will begin to flash. This will allow you to adjust the
temperature of the bottom zone. Adjustment to the lower
zone can be made immediately if Light (5) is touched after
entering Set Temperature mode.
flash. This will allow you to adjust the temperature of the top
zone. After 10 seconds of inactivity, the bottom bar of the F in
“°F” will begin to flash. This will allow you to adjust the
temperature of the bottom zone. Adjustment to the lower
zone can be made immediately if Light (5) is touched after
entering Set Temperature mode.
2. While the top or bottom bar of the F in “°F” is flashing touch
Warmer (2) or Cooler (4) as required to adjust the set-point
temperature. The change will be committed five seconds after
adjustment. The new set-point will be displayed.
temperature. The change will be committed five seconds after
adjustment. The new set-point will be displayed.
Temperature °F °C Selection.
The display may be adjusted to allow for temperature display in
either °F or °C.
either °F or °C.
Touch and hold LIGHT (5) and simultaneously within five
seconds touch and release COOLER (4) three times to change
the displays (3 & 6) as needed.
seconds touch and release COOLER (4) three times to change
the displays (3 & 6) as needed.
Temperature Display.
To display actual temperature:
1. Touch and hold WARMER (2) for approximately five seconds
and release when “°F” begins to flash.
2. The displays (3 & 6) will show a readings for the displays
respective zone.
Product Operation
1
2
3
5
4
6
Upper
Lower