U-Line 2115WCOL2 Manuale Utente
6
2115WC and 2115WCOL2, 2175WC and 2175WCOL2
If Service is Required
If you do not understand a troubleshooting remedy, or
your product needs service, contact U-Line Corporation
directly. Contact information appears on the rear cover of
this guide.
your product needs service, contact U-Line Corporation
directly. Contact information appears on the rear cover of
this guide.
You will be asked for your product Model and Serial
Numbers. This information should be recorded inside the
front cover of this guide, following the products original
purchase. It also appears on the Model and Serial number
plate located on the upper right or rear wall of the
interior of your product.
Numbers. This information should be recorded inside the
front cover of this guide, following the products original
purchase. It also appears on the Model and Serial number
plate located on the upper right or rear wall of the
interior of your product.
When you need replacement parts, always request that
genuine U-Line replacements be used. U-Line products
have been designed and engineered using components
that work efficiently, and provide superior service life and
performance. The use of aftermarket parts or components
may affect the safety, operation, performance or
durability of your product, and may also void its warranty.
genuine U-Line replacements be used. U-Line products
have been designed and engineered using components
that work efficiently, and provide superior service life and
performance. The use of aftermarket parts or components
may affect the safety, operation, performance or
durability of your product, and may also void its warranty.
Figure 2
IMPORTANT
IMPORTANT
Proper air flow (Figure 2) is required for your unit to
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.
Initial Startup
All U-Line units are shipped with controls that are preset.
No initial adjustments are required.
No initial adjustments are required.
IMPORTANT
IMPORTANT
U-Line recommends the unit be allowed to run
overnight prior to loading with product.
overnight prior to loading with product.
Figure 3
To turn the unit on or off, touch and hold the POWER icon
(Figure 3, 1) on the display panel for approximately five
seconds until the °F symbol flashes and release.
(Figure 3, 1) on the display panel for approximately five
seconds until the °F symbol flashes and release.
• A small LED above the icon will illuminate to confirm
the touch of any controller icon.
• The display (Figure 3, 3) will show the unit set-point
temperature when the unit is on and will show OFF
when the unit is off.
when the unit is off.
• Turning the unit off will override any other control
function.
Interior Lighting
The interior of the cabinet can be illuminated whenever
the door is opened (default mode), illuminated for a four-
hour period, or remained darkened (blackout model).
the door is opened (default mode), illuminated for a four-
hour period, or remained darkened (blackout model).
The LIGHT icon (Figure 3, 5) on the control panel is used
to change the lighting functions.
to change the lighting functions.
To turn the lights and display OFF (blackout mode):
1. Touch and hold the LIGHT icon (Figure 3, 5) for ten
seconds and release (the °F symbol will flash briefly at
the end of the five second period).
the end of the five second period).
2. The interior light and control display (Figure 3, 3) will
go dark.
NOTE: Although the display will not be visible, the
temperature controls in the unit remain active, and the
interior temperature will be maintained.
temperature controls in the unit remain active, and the
interior temperature will be maintained.
3. To exit the blackout mode before the 36-hour period,
repeat Step 1.
To illuminate the interior of the cabinet for a four-hour
period:
period:
1. Touch and release the LIGHT icon (Figure 3, 5) to
switch from door-operated lighting control to
continuous lighting (the °F symbol will flash briefly
after the LIGHT icon is pressed).
continuous lighting (the °F symbol will flash briefly
after the LIGHT icon is pressed).
2. To return to door-operated lighting control before the
four-hour period is up, repeat Step 1.
5 Replacement Parts
6 Operation
ULIN_0080_A
1
2
3
5
4
ULIN_0184_A