U-Line 0 U-CLRCO2175B-40 Manuale Utente
u-line.com
3
Air Flow
NOTICE
The unit requires proper air flow to perform at its highest
efficiency. Do not block the front grille or internal fans at
any time, or the unit will not perform as expected. Do not
install the unit behind a door.
efficiency. Do not block the front grille or internal fans at
any time, or the unit will not perform as expected. Do not
install the unit behind a door.
Initial Startup
All U-Line controls are preset at the factory. Initial startup requires
no adjustments.
no adjustments.
NOTICE
U-Line recommends allowing the unit to run overnight
before loading refrigerator or freezer with product.
before loading refrigerator or freezer with product.
To turn the unit on or off, press and hold the POWER icon (1) for
about ten seconds and release. The display will show the unit set-
point temperature on Combo models, and ICE on Clear Ice
models when turned on and display “OFF” when the unit is off.
about ten seconds and release. The display will show the unit set-
point temperature on Combo models, and ICE on Clear Ice
models when turned on and display “OFF” when the unit is off.
Electronic Control Panel
Digital Display. The electronic control with digital display on
Combo models shows a single continuous set-point temperature,
or on Clear Ice models it shows “ICE”. The set point is for the
middle zone, it is a base number used by the controller to maintain
the multiple temperature zones in the unit. The factory default set-
point for Refrigerator models is 38°F. The set-point temperature is
a gauge for further temperature adjustments.
Combo models shows a single continuous set-point temperature,
or on Clear Ice models it shows “ICE”. The set point is for the
middle zone, it is a base number used by the controller to maintain
the multiple temperature zones in the unit. The factory default set-
point for Refrigerator models is 38°F. The set-point temperature is
a gauge for further temperature adjustments.
Adjusting Air Temperature
CLRCO2175
NOTICE
Adjust the set point temperature in single increments,
and wait 24 hours for the temperature to stabilize before
rechecking.
and wait 24 hours for the temperature to stabilize before
rechecking.
Note: The CLRCO2175 refrigerator zone temperature is adjustable. The
ice storage bin temperature in the CLRCO2175 or CLR2160 is not
adjustable.
To adjust the set point temperature:
1. Press and release either WARMER
(2) or COOLER
(4)
to put the controller in the SET TEMPERATURE mode. The
display (3) will begin to flash the °F (or °C) symbol.
display (3) will begin to flash the °F (or °C) symbol.
NOTE: This mode will self-cancel in five seconds, and the
display (3) will show the original set point temperature.
display (3) will show the original set point temperature.
2. Within five seconds (while the °F (or °C) symbol is flashing),
press WARMER
or COOLER
as required to adjust the
set point temperature.
3. The change sets five seconds after adjusting the temperature,
and the display (3) will show the new set point temperature.
Temperature °F °C Selection. U-Line products supplied for
110 VAC have temperatures displayed (3) by default in Fahrenheit
(°F). Models supplied for 220 VAC have temperatures displayed (3)
by default in Celsius (°C).
110 VAC have temperatures displayed (3) by default in Fahrenheit
(°F). Models supplied for 220 VAC have temperatures displayed (3)
by default in Celsius (°C).
Easily adjust the display for either type temperature display.
1. Press and hold LIGHT
(1) and simultaneously within five
seconds press COOLER
(5) three times to change the
display (3) as needed.
Temperature Display. The digital display shows set-point. air
temperature. Under normal operating conditions the temperature
will fluctuate based on a number of factors including door
openings, product load, room temperature, and humidity. The
temperature will always be cool toward the top and coolest
toward the bottom.
temperature. Under normal operating conditions the temperature
will fluctuate based on a number of factors including door
openings, product load, room temperature, and humidity. The
temperature will always be cool toward the top and coolest
toward the bottom.
To display actual temperature:
1. Press WARMER
(2) for five seconds. The display (3) will
indicate the actual temperature.
2. After about 10 seconds, the set point temperature will return to
the display.
Product Operation
1
2
3
5
4