Sharp R-21JCA-F Manuale Utente
R-21JCA-F
16
DESCRIPTION OF LSI
LSI
The I/O signal of the LSI is detailed in the following table.
The I/O signal of the LSI is detailed in the following table.
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
Control Unit
Control unit consists of LSI, power source circuit, synchroniz-
ing signal circuit, reset circuit, buzzer circuit, encoder circuit
and indicator circuit.
Control unit consists of LSI, power source circuit, synchroniz-
ing signal circuit, reset circuit, buzzer circuit, encoder circuit
and indicator circuit.
1) LSI
This LSI controls the encoder signal, relay driving signal for
oven function, buzzer signal and LED signal.
oven function, buzzer signal and LED signal.
2) Power Source Circuit
This circuit generates voltage necessary in the control unit.
Symbol
Voltage
Application
VC
+5V (*)
LSI(I-1)
VR
+20V (*)
RELAY(RY1, RY2)
(*) The voltage under the condition when all LEDs light up.
The voltage VR will vary according to the quantity of the
LEDs which light up.
LEDs which light up.
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in order
to compose a basic standard time in the clock circuit. It
accompanies a very small error because it works on
commercial frequency.
to compose a basic standard time in the clock circuit. It
accompanies a very small error because it works on
commercial frequency.
4) Reset Circuit
A circuit to generate a signals which resets the LSI to the
initial state when power is supplied.
initial state when power is supplied.
5) Buzzer Circuit
The buzzer is responsive to signals from the LSI to emit
audible sounds (completion sound).
audible sounds (completion sound).
6) Door Sensing Switch
A switch to “tell” the LSI if the door is open or closed.
7) Relay Circuit
To drive the magnetron, fan motor, antenna motor and light
the oven lamp.
the oven lamp.
8) Encoder
The encoder generates the pulse signal, and the pulse
signal is sent to the LSI.
signal is sent to the LSI.
9) Indicator Circuit
Indicator elements are the Light-emitting diodes (LD1-
LD20).
This circuit consists of 4-digits and 5 segments.
LD20).
This circuit consists of 4-digits and 5 segments.
Pin No.
Signal
I/O
Description
1
D3
OUT
Segment data signal.
Signal is input to the cathodes of the light-emitting diodes (LD1, LD6, LD11 and LD16).
Signal is input to the cathodes of the light-emitting diodes (LD1, LD6, LD11 and LD16).
2
D4
OUT
Digit selection signal.
Signal is input to the anodes of the light-emitting diodes (LD16 - LD20).
Signal is input to the anodes of the light-emitting diodes (LD16 - LD20).
3
D5
OUT
Digit selection signal.
Signal is input to the anodes of the light-emitting diodes (LD11 - LD15).
Signal is input to the anodes of the light-emitting diodes (LD11 - LD15).
4
D6
OUT
Digit selection signal.
Signal is input to the anodes of the light-emitting diodes (LD6 - LD10).
Signal is input to the anodes of the light-emitting diodes (LD6 - LD10).
5
D7
OUT
Digit selection signal.
Signal is input to the anodes of the light-emitting diodes (LD1 - LD5).
Signal is input to the anodes of the light-emitting diodes (LD1 - LD5).
6
P20
IN
Connected to VDD terminal.
7
P21
IN
Connected to VSS terminal.
8
P22
IN
Signal coming from encoder.
When the encoder is turned, the contacts of encoder make pulse signals. And pulse
signals are input into P22.
When the encoder is turned, the contacts of encoder make pulse signals. And pulse
signals are input into P22.