Frigidaire 316495062 Manuale Utente
1 MOUNTING
SPACE
This Microwave Oven/Hood requires a mounting space on
a wall as shown in Figure 1. It is designed to be used with
standard 12" wall cabinets.
a wall as shown in Figure 1. It is designed to be used with
standard 12" wall cabinets.
Backsplash
Figure 1
15.5"
30" or more
from cooking
surface
30"
At least 2"
12"
BEFORE YOU BEGIN
•
IMPORTANT
Save these instructions for local
inspector’s use.
•
IMPORTANT
Observe all governing codes and
coordinates.
•
NOTE TO INSTALLER
– Be sure to leave these
instructions with the Consumer.
•
NOTE TO CONSUMER
– Keep these instructions for
future reference.
•
SKILL LEVEL
– Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered
under the Warranty.
• Please read all instructions thoroughly before installing
the Over the Range Microwave Oven. Two people are
recommended to install this product.
recommended to install this product.
•
If a new electrical outlet is required, its installation should be
completed by a qualifi ed electrician before the Microwave
Oven is installed. See 3 ELECTRICAL GROUNDING
INSTRUCTIONS on page 2.
completed by a qualifi ed electrician before the Microwave
Oven is installed. See 3 ELECTRICAL GROUNDING
INSTRUCTIONS on page 2.
Read these instructions completely and carefully.
INSTALLATION INSTRUCTIONS
Over The Range Microwave Oven
2 WALL
CONSTRUCTION
This Microwave Oven/Hood should be mounted against and
supported by a fl at vertical wall. The wall must be fl at for
proper installation. If the wall is not fl at, use spacers to fi ll in
the gaps. Wall construction should be a minimum of 2" x 4"
wood studding and ³⁄
supported by a fl at vertical wall. The wall must be fl at for
proper installation. If the wall is not fl at, use spacers to fi ll in
the gaps. Wall construction should be a minimum of 2" x 4"
wood studding and ³⁄
8
" or more thick dry wall or plaster/lath.
The mounting surfaces must be capable of supporting weight
of 110 pounds—the oven and contents—AND the weight of
all items which would normally be stored in the top cabinet
above the unit.
of 110 pounds—the oven and contents—AND the weight of
all items which would normally be stored in the top cabinet
above the unit.
The unit should be attached to a minimum of one 2" x 4"
wall stud or two 2" x 3" wall studs.
wall stud or two 2" x 3" wall studs.
To fi nd the location of the studs, one of the following methods
may be used:
may be used:
A. Use a stud finder, a magnetic device which locates the
nails in the stud.
B. Use a hammer to tap lightly across the mounting surface
to find a solid sound. This will indicate stud location.
The center of the stud can be located by probing the wall with
a small nail to fi nd the edges of the stud and then placing a
mark halfway between the edges. The center of any adjacent
studs will normally be 16" or 24" to either side of this mark.
a small nail to fi nd the edges of the stud and then placing a
mark halfway between the edges. The center of any adjacent
studs will normally be 16" or 24" to either side of this mark.
66" or more
from floor
316495062
TINSEB221WRRZ-EL91
Printed in Thailand
NEED HELP?
For customers in the United States and Canada
United States: 1-800-944-9044
Canada: 1-800-265-8352
United States: 1-800-944-9044
Canada: 1-800-265-8352
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
OTR 1.7 [USA].indd E1
OTR 1.7 [USA].indd E1
4/27/09 5:01:31 PM
4/27/09 5:01:31 PM