Garmin 3880 Manuale Utente
Install Software for a USB Connection
Your printer software works with Windows
®
7, Windows
Vista
®
, XP Professional x64 Edition,
Windows
XP, and Macintosh
®
OS X 10.4.11 to 10.6. If you are using the USB interface, follow the
steps below to install the printer software. If you are using the Ethernet
®
interface, follow the steps in
Chapter 1 of the User's Guide to configure the printer and install the software.
Macintosh
1
Make sure your Macintosh and printer are turned on.
2
Connect the USB cable. Use any open USB port on your computer. Make sure the Epson
Stylus Pro 3880 is securely connected.
Stylus Pro 3880 is securely connected.
3
Insert the Epson Stylus Pro 3880 software CD.
4
Double-click the
Epson icon.
5
Click Install.
Note:
If you see the message that the installer has detected an older version of EpsonNet Config on
your system, you must uninstall the old version before you can install the new one. To uninstall, drag
the EpsonNet folder to the trash. Then reinstall your printer software.
6
Follow the on-screen instructions to install all the necessary software and manuals, register your
printer, and place a link to Special Offers on your desktop.
printer, and place a link to Special Offers on your desktop.
7
Restart the Macintosh when prompted.
Note:
If you're using Mac OS X 10.4, open the Printer Setup Utility. Then click Add and select
your printer. When your Macintosh finds the driver, click the Add button.
Epson Stylus
®
Pro 3880
Unpack
1
Make sure you have these items:
Warning:
The printer weighs about 43 pounds (20 kilograms) and should be lifted and moved
by two people.
Note:
Do not open ink cartridge packages until you are ready to install the ink. Cartridges are
vacuum packed to maintain reliability.
2
Remove all the packing materials and tape.
Check carefully for all the tape inside and
outside the printer. Save the box and packaging
in case you need to ship the printer.
Check carefully for all the tape inside and
outside the printer. Save the box and packaging
in case you need to ship the printer.
3
Open the top cover and remove the carriage retainer bracket. Then close the cover.
Turn On the Printer
1
Connect the power cable. (Do not connect the printer cable yet.)
2
Press the Power button.
After a minute, the ink cover is
automatically released.
automatically released.
Install Ink Cartridges
1
Lift the ink cover.
Note:
If the ink cover is locked, press the
Ink
cover open button on the control panel to release it.
2
Unpack the 9 ink cartridges and shake each one gently.
3
Install each cartridge in the correct slot for its color. The arrow mark should be on top and
pointing into the printer.
pointing into the printer.
Caution:
Do not touch the green chip on top of the cartridge.
Push each cartridge
in until it clicks.
in until it clicks.
Arrow
4
After you install all 9 ink cartridges, close the cover.
The printer starts charging the ink. This takes 7 or 8 minutes. The LCD displays READY
when charging is complete.
when charging is complete.
Caution:
Do not turn off or unplug the printer while the power light is flashing and you see the
message CHARGING INK on the LCD. Also, do not lift the ink cover or load paper during the process.
Note:
The first time you install ink cartridges, the printer uses some ink to charge the printing system,
so print yields may be lower with the first cartridges. Subsequent ink cartridges will last for their full
rated life.
Start Here
Start Here
User's Guide
Limited Warranty
Rear sheet guide
Ink cartridges
Power cord
CD-ROM
Printer
Press the front
cover to open it.
cover to open it.
Ink cover