Land Pride RCPM2660 Manuale Utente
38
Section 6: Maintenance & Lubrication
RCP2660, RCPM2660, RCP3060 and RCPM3060 Parallel Arm Rotary Cutter 316-111M
12/16/08
Land Pride
Refer to Figure 6-2:
7.
Start by assembling blades without shim (#2). Insert
blade bolt (#1) through blade (#3), dish pan (#4) and
flat washer (#5). Temporary secure blade with a used
1 1/8"-12 nut. Draw nut up snug. Do not tighten.
blade bolt (#1) through blade (#3), dish pan (#4) and
flat washer (#5). Temporary secure blade with a used
1 1/8"-12 nut. Draw nut up snug. Do not tighten.
8.
Check blade deflection. If deflection is greater than
3/4", remove blade bolt and reassemble as before
except include shim (#2) in the assembly. Select
shim thickness based on deflection. The greater the
deflection, the thicker the shim.
3/4", remove blade bolt and reassemble as before
except include shim (#2) in the assembly. Select
shim thickness based on deflection. The greater the
deflection, the thicker the shim.
9.
Once blade deflection is correct, replace used nut
with new locknut (#6) and torque to 450 ft. lbs.
with new locknut (#6) and torque to 450 ft. lbs.
10. If replacing dishpan (#4), nut on gearbox output shaft
should be torqued to 550 ft./lbs. and cotter pin
installed in nut with legs securely bent around nut.
installed in nut with legs securely bent around nut.
Cutter Blade Assembly
Figure 6-2
IMPORTANT: Examine blade bolts (#1) and
washers (#5) for excessive wear and replace if worn.
washers (#5) for excessive wear and replace if worn.
IMPORTANT: Locknuts can loose their ability to
lock properly once removed. Therefore, always use
a used blade nut or plain nut in steps step 7 & step
8 below and then replace used nut with new
locknut in step step 9.
lock properly once removed. Therefore, always use
a used blade nut or plain nut in steps step 7 & step
8 below and then replace used nut with new
locknut in step step 9.
3/4" maximum
blade deflection
when blade
bolts are tight
Land Pride Cutter Blade Parts
Item Part No.
Part Description
318-586A
BLADE BOLT KIT
(Includes items 1, 2, 5, & 6 below)
(Includes items 1, 2, 5, & 6 below)
1
802-277C
BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY
2
312-075D
BLADE SPACER 16 GA. (.060")
2
312-082D
BLADE SPACER 18 GA. (.048")
2
312-089D
BLADE SPACER 20 GA. (.036")
2
312-808D
BLADE SPACER 24 GA. (.024")
3
820-112C
CUTTER BLADE 1/2 x 4 x 25 CW
4
316-124H
DISHPAN WELDMENT SPCL-HUB
5
804-147C
WASHER FLAT 1 HARD ASTMF436
6
803-170C
NUT HEX TOP LOCK 1 1/8-12 PLATE
Skid Shoes
!
WARNING
Excessive wear on skid shoes may cause inadequate operation
of cutter and create a safety hazard!
of cutter and create a safety hazard!
Inspect skid shoes at the beginning of each cutting
season. Check all skid shoes weekly for wear and
replace if necessary. Original material thickness is 1/4".
They should be replaced when the material thickness is
less than 1/8" at any point. They are interchangeable
from left to right.
season. Check all skid shoes weekly for wear and
replace if necessary. Original material thickness is 1/4".
They should be replaced when the material thickness is
less than 1/8" at any point. They are interchangeable
from left to right.
Order only genuine Land Pride parts from your local
Land Pride Dealer.
Land Pride Dealer.
Refer to Figure 6-3:
Replace wing skid shoes as follows:
1.
Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2)
and skid shoe (#1) as shown.
and skid shoe (#1) as shown.
2.
Plow bolts should be checked for wear and replaced if
necessary.
necessary.
3.
Attach new skid shoe (#1) to cutter with existing
3/8” plow bolts (#2) and secure with 3/8" hex whiz
nuts. Torque to 31 ft. lbs.
3/8” plow bolts (#2) and secure with 3/8" hex whiz
nuts. Torque to 31 ft. lbs.
4.
Repeat on opposite side.
Wing Skid shoe
Figure 6-3
Land Pride Skid Shoe Replacement Parts
Part No.
Part Description
312-602D
SKID SHOE
802-466C
PLOW BOLT, 3/8" - 16 x 1 1/1/4" grade 5
24623