BreatheAudio BA-LRC1 Manuale Utente

6. If the device responds, go to step 6. If the device does not respond, 
     press CH+. The remote will try the next code. Continue until the device 
     responds.

NOTE: Press CH- to try the previous code.
7. To set the code, press SETUP once. The LED blinks twice.
8. To search for other device codes, repeat steps 1 to 6.

If you have set up the remote using the procedure in “Searching For Your 

Code”, you may need to find out which five-digit code is operating your 

equipment.

For example, to find out which code is assigned to your TV:
1. Press SOURCE A once.
2. Press  and hold SETUP until the red LED blinks twice, then release.
3. Enter 990. The LED blinks twice.
4. To view the code for the first digit, press numeric key 1. Count the LED 
     blinks (for example, three blinks = 3), and write down the number in 
     the  appropriate code listing in step 8 under “Programming a Device”.

NOTE: If a code digit is 0, the LED does not blink.
5. Repeat step 4 for the four remaining digits, using 2 for the second 
     digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth 

     digit.

6. To check for other device codes, repeat steps 1-5, substituting 
     Sources A or B.

Changing Volume Lock
The BA-LRC1 comes preset to allow independent volume control of each 
selected device (Global Volume Unlock). However, you may change the Volume 
Lock setting to Global Volume Lock so that one source’s volume will control 
volume in all other modes. After that, you can perform Individual Volume Unlock 
on a selected source to set its volume control for independent operation or 
Global Volume Unlock to remove all volume locking.

Locking Volume Control to One Mode (Global Volume Lock)
1. Press and hold SETUP until red LED blinks twice, then release.
2. Enter 993 and then press the mode key for the source you want to 
     control volume (for example, CD). The LED blinks twice. Now, when 
     you press VOL+, VOL- or Mute, the selected source (for example, CD) 

     will control the volume regardless of the current mode.

Unlocking All Volume Control (Restoring Global Unlock)
1. Press and hold SETUP until the red LED blinks twice, then release.
2. Enter 993 and then press VOL+. The LED blinks four times. Volume is  
     independently controlled for all programmed sources.

Unlocking a Single Source’s Volume Control
1. Press a source key (A or B).
2. Press and hold SETUP until the red LED blinks twice, then release.
3. Enter 993 and then press VOL-. The LED blinks four times. Volume is 
independently controlled for the selected sources.

A macro can be used to control a home theater operation, to set a favorite 
channel, or for other multiple functions you would like to control with one key 
press. You can use any key to activate a macro. Moreover, each Macro Key 
can hold up to 32 key presses total.
You can program a macro that will operate regardless of what mode you are in, 
or one that will only operate when you are in a specific mode.
NOTE: Programming a new macro over an existing one will erase the original 
macro.

Programming a Mode-Independent Macro
1. Press and hold SETUP until the red LED blinks twice, then release.
2. Press 995. The LED blinks twice.
3. Press the key you want to use to activate your macro (POWER, any 
    unused key, etc.).
4. Enter the series of commands you want the macro to execute (up to 32 

    commands).
5.Press and hold SETUP until the red LED blinks twice, then release.

Now, when you press the Macro key, the remote will send the series of 
commands you have entered, regardless of what mode you are in. For 
example, you could program the Macro key to turn on both your TV and cable 
box and select a particular channel.
To clear the macro, repeat steps 1 to 5 above, but do not enter a series of 
commands at step 4.

Programming a Mode-Dependent Macro
1. Press a source key (A or B). 
2. Press and hold SETUP until the red LED blinks twice.
3. Press 978. The LED blinks twice.
4. Press the key you want to use to activate your macro (POWER, any 
    unused key, etc.).

5. Enter the series of commands you want the macro to execute (up to 32 
    commands).
6. Press and hold SETUP until the red LED blinks twice, then release.

 

 

Switch the device input to view TV 
or video programs.

Directly enter channels 
(For example, 09 or 31).
Press ENTER to send channel 
number entries on some TV models.

Macro device keys can be used to 

dedicate multiple string macro 

commands.

Whole-Home Control is dedicated 

control of your BreatheAudio 

System. MUTE, VOL-, VOL+, 

ON/OFF duplicate the BreatheAudio 

zone keypad functions.

To control devices, A and B, follow these steps.

Before proceeding, find the codes for the devices you want to program in 

“Manufacturer’s Codes” in the following pages and write them down or 
highlight them.
NOTE: Any device may be set up on any mode key.

Whole-Home Control

1. Turn on the device (for example, CD player) and, if needed, load   

    media (for example, a CD).
2. Press a device key (A or B).
3. Press and hold SETUP until the red LED blinks twice, then release.

4. Enter the first five-digit code for your device. The red LED blinks once 
    as each digit is entered. If the code is correct, the LED blinks twice.
NOTE: If the LED does not blink twice, repeat steps 2 to 4 and try 
entering the code again.
5. Aim the remote at the device and press POWER. The device should 

    turn off. If it does not, repeat steps 3 to 5, trying each code for your   
    brand until you find one that works. If you cannot find a code that 
    works, see “Searching For Your Code”. 

6. Repeat steps 1 to 5 for the other devices you want to control. For 
     Future reference, write down each working device code below:

If your device does not respond to the remote after trying all codes listed 

for your brand, or if your brand is not listed, try searching for your code:

1. Press a device key once.
2. Press and hold SETUP until the red LED blinks twice, then release.
3. Enter 991. The LED blinks twice.
4. Enter the device group number:

5. Select a test function, such as POWER or PLAY. The remote sends IR 

     codes from its library to the selected device, starting with the most  

     popular code first.

 

 

 

 

 

 

SOURCE A Code:

Desc. _______

SOURCE B Code:
Desc. _______

TV (TVs)

VCR (VCRs, DVD players) 

0

Cable (Cable Converters, Video Accessories, Satellite 

Receivers).

1

2

Audio (Audio Amplifiers, Audio Amp/Tuners, CD players)

3