Casio 1361 Manuale Utente

▲

▼

▲

Alarm on indicator

Minutes

Hourly Time Signal on
indicator

C

A

D

B

Hour

Mode
indicator

When the Daily Alarm is switched on, the alarm sounds for 20 seconds at the preset
time each day.  Press any button to stop the alarm after it starts to sound. When the
Hourly Time Signal is switched on, the watch beeps every hour on the hour.
Note that the Daily Alarm and the Hourly Time Signal operate based on the digital time
setting.

3. Press 

C

 to change the selection in the following sequence.

Hour

Minutes

4. Press 

D

 to increase the selected digits and 

B

 to decrease them.  Holding down

either button changes the number at high speed.

• The format (12-hour and 24-hour) of the alarm time matches the format you select

for normal timekeeping.

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as morning or afternoon (indicated as “

” on the display).

5. After you set the alarm time, press 

A

 to return to the normal Alarm Mode (the

flashing stops).

The following shows how the display automatically changes if you do not operate any
button for a few minutes while in the Alarm Mode.

Timekeeping 
Mode

A few

minutes

Alarm time setting
(Flashing)

Normal Alarm Mode
(No flashing)

A few

minutes

Press 

B

 while in the normal Alarm Mode (when no digit is flashing) to change the

status of the Daily Alarm and Hourly Time Signal in the following sequence.

Hourly Time
Signal only

Daily Alarm
only

Both off

Both on

Press any button to stop the alarm after it starts to sound.

1. Hold down 

D

 while in the normal Alarm Mode to sound the alarm.

2. While holding down 

D

, press 

B

 to switch between the three available alarm tones.

The last alarm tone that is sounding is selected when you release 

D

.

The Stopwatch Mode lets you measure elapsed time,
split times, and two finishes.  The range of the stop-
watch is 23 hours, 59 minutes, 59.99 seconds.

1. Press 

D

 to start the stopwatch.

2. Press 

D

 to stop the stopwatch.

• You can resume the measurement operation by

pressing 

D

 again.

3. Press 

B

 to clear the stopwatch to all zeros.

1/100 second

▲

▲

▼

Hours

Minutes

Seconds

C

A

Mode indicator

D

B

1. Press 

D

 to start the stopwatch.

2. Press 

B

 to display the timing up to that point.  Stopwatch timing  continues internally.

• At this time, the display also changes from “

” to “

”, indicating that the

split time is being recorded.

• Split time is cleared if you exit the Stopwatch Mode during the timing operation.

3. Press 

B

 to clear the split time and to continue time measurement on the display.

• You can repeat steps 2 and 3 as many times as you want.

4. Press 

D

 to stop the time measurement.

5. Press 

B

 to clear the stopwatch to all zeros.

When the time shown on the display does not match

the analog setting, use this mode to correct this situa-
tion by changing the analog setting.

1. Make sure that the watch is in the Hand Setting

Mode.  If not, use 

C

 to enter the Hand Setting

Mode.

2. Hold down 

A

 while in the Hand Setting Mode until

the indicator “

” starts to flash on the dis-

play.

▼

▲

Current date

Minute hand

Hour hand

Mode

indicator

Current time

C

D

B

A

3. Press 

D

 to advance the hands of the analog timepiece.

4. After you set the analog time, press 

A

 to return to the normal Hand Setting Mode

(the flashing stops).

• The following shows how the display automatically changes if you do not operate

any button for a few minutes while in the Hand Setting Mode.

Timekeeping 
Mode

A few

minutes

Hand time setting
(the indicator flashes)

Normal Hand Setting Mode
(the flashing stops)

A few

minutes

The following shows how the display of module 1361 changes for about 20 seconds
when a Reminder signal sounds.

• The display changes similarly when a Schedule Memo signal sounds, or when a

daily alarm sounds in the Timekeeping Mode.  When a Schedule Memo signal
sounds, time of the nearest scheduled appointment appears, instead of the current
time.

The Auto Display function of this watch continually changes the contents of the digital
display.  Note that you cannot use any of the watch’s other function while the Auto
Display function is operating.

Hold down 

C

 for about three seconds in any mode

until the watch beeps.

Hold down 

C

 for about three seconds until the watch

beeps.  At this time, the watch is in the Timekeeping
Mode.

Note
The Auto Display function cannot be performed while you are making settings (i.e.
while digits or other settings are flashing on the display).

C

A

D

B

1. Make sure that the watch is in the Alarm Mode.  If

not, use 

C

 to enter the Alarm Mode.

2. Hold down 

A

 while in the Alarm Mode until the

hour digits start to flash on the display.  The hour
digits flash because they are 

selected.  At this

time the Daily Alarm is switched on automatically.

1. In the Schedule Memo Mode, use 

B

 or 

D

 to scroll through the data items and

display the one you want to delete.

2. Press 

A

 and the month digits begin to flash because they are selected.

3. Press 

B

 and 

D

 at the same time.  The watch beeps and the message “

”

appears on the display, indicating that the item is deleted.  At this time, the cursor
appear on the display, ready for input.

4. Input data or press 

A

 to return to the normal Schedule Memo Mode (the flashing

stops).

1. Press 

D

 to start the stopwatch.

2. Press 

B

 when the first finisher crosses the line, and record the time.

3. Press 

D

 when the second finisher crosses the line.

4. Press 

B

 to display the finishing time of the second finisher.

5. Press 

B

 again to clear the stopwatch to all zeros.