Braun 603A Manuale Utente
Page 18
WA
RN
ING
81823
Push T-handle in fully and
manually move platform in
and out to engage platform
lock before driving vehicle.
Failure to lock platform may
result in unintended platform
deployment. Unintended
platform deployment may
result in serious bodily injury
and/or property damage.
manually move platform in
and out to engage platform
lock before driving vehicle.
Failure to lock platform may
result in unintended platform
deployment. Unintended
platform deployment may
result in serious bodily injury
and/or property damage.
Do not remove!
TO
LOCK
TU
RN
Manual Operating Instructions
A
Hand
Pump
Hand Pump Handle
Release Valve
maximum
30 inch lbs
minimum
15 inch lbs
seats
(stops)
O
P
E
N
C
L
O
S
E
approximate 1/16" intervals
Valve Tightening Specification:
Once valve seats (stops), tighten
15 to 30 inch pounds as shown.
Once valve seats (stops), tighten
15 to 30 inch pounds as shown.
Figure 1
Figure 2
WA
RN
ING
81823
Push T-handle in fully and
manually move platform in
and out to engage platform
lock before driving vehicle.
Failure to lock platform may
result in unintended platform
deployment. Unintended
platform deployment may
result in serious bodily injury
and/or property damage.
manually move platform in
and out to engage platform
lock before driving vehicle.
Failure to lock platform may
result in unintended platform
deployment. Unintended
platform deployment may
result in serious bodily injury
and/or property damage.
Do not remove!
TO
LO
CK
TURN
Open
(Down)
Close
(Up/Stop)
B
C
b
a
a
b
Hand Pump Handle
To Manually Lower Platform
To Ground Level:
To Ground Level:
Note: Disregard procedures for
manually moving the platform in or
out if not applicable.
manually moving the platform in or
out if not applicable.
When lowering platform from
floor level:
floor level:
1. a. Pull “T” handle release cable
outward and b. turn “T” handle
to lock platform into the re-
leased position (see Figure 1).
to lock platform into the re-
leased position (see Figure 1).
2. Pull platform out fully (until it
stops), if applicable.
3. Reengage the release cable
mechanism by a. turning the “T”
handle and b. pushing the “T”
handle in fully (see Figure 2).
handle and b. pushing the “T”
handle in fully (see Figure 2).
Note: Grasp the outer roll stop
and move the platform in and
out until the platform locks.
You will feel the release mecha-
nism engage. Read Platform
Carriage Assembly Drive
Chain Reengagement Proce-
dure section on page 16!
and move the platform in and
out until the platform locks.
You will feel the release mecha-
nism engage. Read Platform
Carriage Assembly Drive
Chain Reengagement Proce-
dure section on page 16!
4. Place slotted end of pump
handle onto hand pump down
(release) valve and turn coun-
terclockwise (open 1/2 turn
only) to lower platform. See
Photo B.
(release) valve and turn coun-
terclockwise (open 1/2 turn
only) to lower platform. See
Photo B.
5. Turn hand pump down (release)
valve clockwise (close) before
performing any other lift func-
tions. See Photo B.
performing any other lift func-
tions. See Photo B.
Note: Close hand pump
release valve securely before
operating lift. The lift will not
operate properly if the valve is
not in its fully clockwise posi-
tion.
release valve securely before
operating lift. The lift will not
operate properly if the valve is
not in its fully clockwise posi-
tion.
Release
Valve