PLUS Vision V3-111 Manuale Utente
E-57
When an Indicator is Lit or Flashing
STANDBY
AUTO
RC
E
STANDBY
STATUS
STANDBY
STATUS
STATUS
STANDBY
STATUS
STANDBY
STATUS
STANDBY
STATUS
STANDBY
The indicators on the projector’s control panel light or flash to
notify of problems, as described below.
An indicator is also used to notify you of the currently set power
mode. See “Power Cable Connections and Switching the Power
On/Off” on page E-22.
notify of problems, as described below.
An indicator is also used to notify you of the currently set power
mode. See “Power Cable Connections and Switching the Power
On/Off” on page E-22.
STATUS indicator
Indicator status
What you should do
Lit red
When the power is on (Lit green)
Standby (Lit amber)
Standby (Lit amber)
Lit red
Flashing amber for 60 seconds, then lit
amber
amber
Flashing red
(lit for 1 seconds/off for 1 seconds)
(lit for 1 seconds/off for 1 seconds)
Lit red
Flashing red
(lit for 0.5 seconds/off for 0.5 seconds)
(lit for 0.5 seconds/off for 0.5 seconds)
Lit red
Flashing red
(lit for 0.5 seconds/off for 0.5 seconds)
(lit for 0.5 seconds/off for 0.5 seconds)
Lit amber
Flashing red
(lit for 1 seconds/off for 1 seconds)
(lit for 1 seconds/off for 1 seconds)
When the lamp has burned out dur-
ing use
Flashing amber for 90 seconds, then lit
amber
When the lamp does not come on
from the start
Lit amber
ing use
Flashing amber for 90 seconds, then lit
amber
When the lamp does not come on
from the start
Lit amber
It is time to replace the lamp.
Replace with a new lamp cartridge.
Replace with a new lamp cartridge.
The lamp has reached the end of its service life. The power
will no longer turn on.
The projector can be used for 100 hours after the lamp has reached
the end of its service life.
Replace with a new lamp cartridge.
will no longer turn on.
The projector can be used for 100 hours after the lamp has reached
the end of its service life.
Replace with a new lamp cartridge.
The lamp cover is open.
The lamp cover is not properly mounted. Mount it properly.
The lamp cover is not properly mounted. Mount it properly.
The temperature is abnormally high.
• The temperature protector has been activated. If the room tem-
• The temperature protector has been activated. If the room tem-
perature is high, move the projector to a cool place. If the
projector’s internal temperature is high, check the cooling fan’s
ventilation slots and clean them if they are clogged.
projector’s internal temperature is high, check the cooling fan’s
ventilation slots and clean them if they are clogged.
• When the temperature protector is activated, the power turns
off and in some cases will not turn back on immediately. In this
case wait about 90 seconds, then try again.
case wait about 90 seconds, then try again.
The fan has stopped.
Unplug the power cable and contact a store that sells the V3-131/
V3-111 for repairs.
Unplug the power cable and contact a store that sells the V3-131/
V3-111 for repairs.
The lamp will not light.
Wait at least 90 seconds, then turn the power back on. If the prob-
lem persists, unplug the power cord and contact a store that sells
the V3-131/V3-111 for repairs.
Wait at least 90 seconds, then turn the power back on. If the prob-
lem persists, unplug the power cord and contact a store that sells
the V3-131/V3-111 for repairs.
STATUS
STANDBY
STANDBY indicator
Should an indicator be in a condition other than normal or flash at a rate other than the aforementioned, disconnect the power
cable and contact your store of purchase.
cable and contact your store of purchase.
STATUS
STANDBY
Flashing amber
(for several seconds)
(for several seconds)
Flashing amber
(for several seconds)
(for several seconds)
The STANDBY button has been pressed with the lens stowed away.
The STANDBY indicator flashes for several seconds, then stops flashing, remain-
ing lit, and the projector is set back to the standby status (with the STATUS indica-
tor off). Press the lens lift button to raise the lens unit, then press the STANDBY
button. The power will now turn on.
The STANDBY indicator flashes for several seconds, then stops flashing, remain-
ing lit, and the projector is set back to the standby status (with the STATUS indica-
tor off). Press the lens lift button to raise the lens unit, then press the STANDBY
button. The power will now turn on.
The lens unit was stowed away while an image was being projected.
The projector automatically turns off, and the indicators continue to flash for 90
seconds. (The cooling fan continues to run during this time.) To turn the projector
back on, wait 90 seconds, press the lens lift button to raise the lens, then press the
STANDBY button. The power turns on.
The projector automatically turns off, and the indicators continue to flash for 90
seconds. (The cooling fan continues to run during this time.) To turn the projector
back on, wait 90 seconds, press the lens lift button to raise the lens, then press the
STANDBY button. The power turns on.