Roland VG-99 Manuale Utente
129
FX (Effects) Chapter 9 Parameters Guide
Chapter 9
T.WAH (Touch Wah)
You can produce a wah effect with the filter changing in response to
the guitar level.
the guitar level.
AUTO WAH
This changes the filtering over a periodic cycle, providing an
automatic wah effect.
automatic wah effect.
OCTAVE
This adds a note one octave lower, creating a richer sound.
*
Because of the need to analyze the pitch, chords (two or more sounds
played simultaneously) cannot be played.
played simultaneously) cannot be played.
Parameter/
Range
Range
Explanation
MODE
Selects the wah mode.
LPF
(Low Pass Filter)
(Low Pass Filter)
This creates a wah effect over a wide fre-
quency range.
quency range.
BPF
(Band Pass Filter)
(Band Pass Filter)
This creates a wah effect in a narrow fre-
quency range.
quency range.
POLARITY
Selects the direction in which the filter will change in response to the
input.
input.
UP
The frequency of the filter will rise.
DOWN
The frequency of the filter will fall.
SENS (Sensitivity)
0–100
Adjusts the sensitivity at which the filter
will change in the direction determined by
the polarity setting.
Higher values will result in a stronger re-
sponse. With a setting of 0, the strength of
picking will have no effect.
will change in the direction determined by
the polarity setting.
Higher values will result in a stronger re-
sponse. With a setting of 0, the strength of
picking will have no effect.
FREQ (Frequency)
0–100
Adjusts the center frequency of the Wah ef-
fect.
fect.
PEAK
Higher values will produce a stronger tone which emphasizes the
wah effect more.
wah effect more.
0–100
Adjusts the way in which the wah effect ap-
plies to the area around the center frequen-
cy. With a value of 50 a standard wah sound
will be produced.
plies to the area around the center frequen-
cy. With a value of 50 a standard wah sound
will be produced.
LEVEL
0–100
Adjusts the volume of the effect sound.
DIRECT LEVEL
0–100
Adjusts the volume of the direct sound.
Parameter/
Range
Range
Explanation
MODE
Selects the wah mode.
LPF
(Low Pass Filter)
(Low Pass Filter)
This creates a wah effect over a wide fre-
quency range.
quency range.
BPF
(Band Pass Filter)
(Band Pass Filter)
This creates a wah effect in a narrow fre-
quency range.
quency range.
FREQ (Frequency)
0–100
Adjusts the center frequency of the Wah ef-
fect.
fect.
PEAK
0–100
Adjusts the amount of wah effect applied in
the range near the reference frequency.
Higher values will produce a stronger tone
which emphasizes the wah effect more.
With a value of 50 a standard wah sound
will be produced.
the range near the reference frequency.
Higher values will produce a stronger tone
which emphasizes the wah effect more.
With a value of 50 a standard wah sound
will be produced.
RATE
0–100,
BPM
–BPM
Adjusts the frequency (speed) of the change.
When set to BPM, the value of each parameter will be set according
to the value of the BPM (p. 163) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
to the value of the BPM (p. 163) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
* If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that
time.
time.
DEPTH
0–100
Adjusts the depth of the effect.
LEVEL
0–100
Adjusts the volume of the effect sound.
DIRECT LEVEL
0–100
Adjusts the volume of the direct sound.
Parameter/
Range
Range
Explanation
RANGE
This selects the register to which the effect is applied.
RANGE1
B1 (corresponds to the sound of an open 7th
string) to E6 (corresponds to the 1st string
played at the 24th fret)
string) to E6 (corresponds to the 1st string
played at the 24th fret)
RANGE2
B1 (corresponds to the sound of an open 7th
string) to E5 (corresponds to the 1st string
played at the 12th fret)
string) to E5 (corresponds to the 1st string
played at the 12th fret)
RANGE3
B1 (corresponds to the sound of an open 7th
string) to E4 (corresponds to the sound of an
open 1st string)
string) to E4 (corresponds to the sound of an
open 1st string)
RANGE4
B1 (corresponds to the sound of an open 7th
string) to E3 (corresponds to the 4th string
played at the 2nd fret)
string) to E3 (corresponds to the 4th string
played at the 2nd fret)
OCTAVE LEVEL
0–100
Adjusts the volume of the sound one octave
below.
below.
DIRECT LEVEL
0–100
Adjusts the volume of the direct sound.
Parameter/
Range
Range
Explanation
VG-99_e.book 129 ページ ２００７年７月５日 木曜日 午前９時２２分