Sharp LC-19DV28UT Manuale Utente

Press POWER on the TV/DVD, or POWER on the 

remote control.

•  POWER indicator (Green): The TV/DVD is on. (“Please 

wait” will appear for a few seconds on the screen.)

Press TV/DVD to select the DVD mode.

Press POWER on the TV/DVD, or POWER on the 

remote control.

•  The TV/DVD enters standby mode and the image on the 

screen disappears.

•  The POWER indicator on the TV/DVD changes to Red.

•  If you are not going to use this TV/DVD for a long period 

of time, be sure to remove the AC cord from the power 

outlet.

•  Weak electric power is still consumed even when the 

power is turned off.

Perform the following steps before you press POWER 

on the remote control unit.

Insert the batteries into the remote control unit. 

(See page 10.)

Plug in the AC cord to the AC outlet. (See page 9.)

Place the disc in the disc slot with the label side 

facing forward. (If the disc has a label.) Hold the 

disc without touching its surface, align it with the 

guides, and place it in position.

•  If a disc is inserted during some modes other than 

DVD mode, it may switch to DVD mode and then 

playback may be begun automatically.

Press DISPLAY. The status display of the disc will 

appear on the screen.

Display messages may change at every time when you 

press DISPLAY for some discs or files.

  Static electricity, etc., may affect the player’s operation. 

Disconnect the AC power cord once, then connect it 

again.

If the unit is slanted or moved while inserting disc, the disc 

may get damage.

•

•  If a non-compatible disc is loaded, “Can’t play disc” or “Incompatible disc region number Can’t play disc” will appear on the 

TV screen according to the type of loaded disc. In this case, check your disc again (see pages 6 and 36).

•  Some discs may take a minute or so to start playback.

•  When an 8 cm disc is placed into the disc slot, and the playback picture or menu display does not appear, press PLAY.

•  A prohibition message “Depending on the disc, this operation may be prohibited” or “This operation can’t be performed” 

may appear at the screen. This message means either the feature you tried is not available on the disc, or the unit cannot 

access the feature at this time. This does not indicate a problem with the unit.

•  When you set a single-faced disc label downwards (i.e. the wrong way up) “Loading” will appear on the display and then 

“Can’t play disc” will be displayed.

•  Some playback operations of DVDs may be intentionally fixed by software producers. Since this TV/DVD plays DVDs 

according to the disc content recorded, some playback features may not be available. Also refer to the instructions supplied 

with the DVDs.

•  Do not move the unit during playback. Doing so may damage the disc.

• Use EJECT to unload and eject the disc.

•  Do not put any objects other than discs on the disc slot. Doing so may cause the unit to malfunction.

•  In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen 

menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press 

POWER on your remote control once the movie is completed.

•  There may be a slight delay between the button is pressed and the function activates.

On the screen, “ ” changes to “Loading” and then 

playback will commence.

•  A menu screen appear on the TV screen, if the disc 

has a menu feature. In this case, press ▲/▼/◀/▶ or 

ENTER to operate a menu feature.

Press STOP to end playback.

•  The unit can record where you stop a video, but it 

depends on a disc you are using. Press PLAY to 

resume a playback point. The unit can store a memory 

of stopped point of last five discs that you have played. 

When one of these discs is next loaded, you can 

resume playback from where you stopped playing last 

time.

•  If you press STOP again (“Resume off” appears on the 

screen), the TV/DVD will clear the stopped point.

•  It is only DVD videos that a stopped point can be 

stored in the unit with.

•  You cannot save a stopped point for some discs. If a 

number of discs played and stored in the unit exceeds 

five, a new memory will overwrite the old stored 

memory.

Press EJECT.

Remove the disc and then press POWER.

The TV/DVD turns off.

•  When you eject the disc, you may hear mechanism 

noise, but it is not malfunction.

54W0131B.indb   29

5/19/10   10:55:57 AM