Manuale UtenteSommarioINTRODUCTION4Phase 5 Coin Microprocessor Controller (Computer) Features4L.E.D. DISPLAY AND CODES8OPERATING INSTRUCTIONS10A. Timed Mode10B. Automatic Mode (Patent No. 4,827,627)11C. Free Dry Mode12PROGRAM SELECTION13Temperature Display Mode13Right Coin Count (rCC)/Left Coin Count (LCC)13Automatic Review of Program Location14PL01 - Temperature Conversion Status15Automatic Mode (Auto) Patent No. 4,827,62715Timed Mode (tInE)15Anti-Wrinkle Program (Grd)16Buzz/Tone (bUZ)16Free Dry Mode Cycle (FrEE)16Coin Mode (Coin)17Flash Display Status (FLS)17Bad Coin Lockout Status (bCLO)17Bad Coin Reset (bCrS)17Accumulative Time (AtIn)18Accumulative Coin (ACOn)20Rotational Safe Guard - OPTIONAL (nSEn)21PL02 - Percent Dry (PdrY)21PL03 - High Temperature (HI° F)21PL04 - High Cool Down Temperature/Time (HIcd)22PL05 - Low Temperature (LO° F)22PL06 - Low Cool Down Temperature/Time (LOcd)22PL07 - Permanent Press (PP° F)22PL08 - Permanent Press Cool Down Temperature /Time (PPCd)22PL09 - Left Coin Slot Denomination (LCdE)22PL10 - Right Coin Slot Denomination (rCdE)23PL11 - Time For Amount To Start (tFAS)23PL12 - Amount To Start (AtSt)23PL13 - Minimum Amount For Additional Time (AFAT)23PL14 - Maximum Time For Automatic Dry (Adrt)23PL15 - Anti-Wrinkle Timing24Guard Delay Time (GdLY)24Guard On Time (Gont)24PL16 - Active Guard Time (AGt)24PL17 - “A” and “b” Factors24PROGRAMMING INSTRUCTIONS25A. Introduction To Programming25B. Programming (Flowcharts)26PROGRAMMING29Temperature Display Mode29Left Coin Count30Right Coin Count31Program Location 01 (PL01)32Program Location 02 (PL02)36Program Location 03 (PL03)37Program Location 04 (PL04)38Program Location 05 (PL05)39Program Location 06 (PL06)40Program Location 07 (PL07)41Program Location 08 (PL08)42Program Location 09 (PL09)43Program Location 10 (PL10)44Program Location 11 (PL11)45Program Location 12 (PL12)46Program Location 13 (PL13)47Program Location 14 (PL14)48Program Location 15 (PL15)49Program Location 16 (PL16) and Program Location 17 (PL17)50FACTORY PRESET PROGRAMS/PARAMETERS51For all dryer models except AD-26/AD-295 and AD-540/WDA-54052For all dryer models except AD-26/AD-295 and AD-540/WDA-54053For dryer models AD-26/AD-295 Only54For dryer models AD-26/AD-295 Only55PHASE 5 COIN SYSTEM DIAGNOSTICS56A. Diagnostic (L.E.D) Failure Codes561. “door”562. “dSFL”563. “SEFL”574. “Hot”57B. L.E.D. Display Indicators/Dots571. Heat Circuit Indicator572. Motor Circuit Indicator57C. Phase 5 Microprocessor Controller (Computer) Relay Output L.E.D. Indicators581. “DOOR”582. “HEAT”593. “MTR” (motor)59“A” AND “B” FACTOR PARAMETERS60OPTIONAL 9 VOLT BATTERY BACKUP62Settings: PL09 (LCdE)25PL11 (tFAS)30PL12 (AtSt)25Settings: PL09 (LCdE)25PL11 (tFAS)30PL12 (AtSt)50(LCdE)10(rCdE)25(tFAS)15(AtSt)25(LCdE)10(rCdE)25(tFAS)14(AtSt)35(LCdE)10(rCdE)25(tFAS)33(AtSt)55(LCdE)10(rCdE)25(tFAS)10(AtSt)35(LCdE)25(tFAS)24(AtSt)50(AFAt)50(LCdE)10(rCdE)25(tFAS)20(AtSt)50(AFAt)20(LCdE)10(rCdE)25(tFAS)14(AtSt)35(AFAt)25Dimensioni: 593 KBPagine: 66Language: EnglishApri il manuale