Manuali utente per ADC Telecommunications Inc. AUAC85

Sommario

• UltraWAVE BTS 6 Installation and Commissioning Guide

  1
  • Welcome!

    9
  • Assumptions, Purpose, and Audience

    9
  • Related Documentation

    9
  • Customer Support Services

    10
  • Conventions Used in this Manual

    12
• One - Unpacking and Configuration Verification

  13
  • 1-1 Unpacking and Inspecting

    13
  • 1-2 Inspect Components and Record Part Numbers

    15
    • 1-2.1 Identifying the System Configuration

      16
    • 1-2.2 Identifying Module Part and Serial numbers

      18
  • 1-3 Verifying and Documenting Cards and Modules

    20
    • 1-3.1 Required Equipment

      20
    • 1-3.2 RF Subrack Assembly

      20
    • 1-3.3 Baseband Subrack Assembly

      20
  • 1-4 Internal Cabling Overview

    22
• Two - Installation

  23
  • 2-1 Site Requirements

    23
    • 2-1.1 Environmental Conditions

      23
    • 2-1.2 Electrical Requirements

      24
    • 2-1.3 Chassis Requirements

      25
  • 2-2 Mounting the BTS Chassis

    26
  • 2-3 Configuring the E1 or T1 Trunk Card

    30
    • 2-3.1 Configure Ground Jumpers on 75 Ohm E1 Cards

      30
    • 2-3.2 Configure Cable Length DIP Switch Settings on T1 Cards

      35
  • 2-4 Connecting Power and Ground Cables

    37
    • 2-4.1 Connecting the Grounding Cable

      37
    • 2-4.2 Connecting the Power Supplies

      37
  • 2-5 Connecting E1 or T1 Trunk Cables

    40
    • 2-5.1 E1 Cables

      40
    • 2-5.2 T1 Cables

      42
    • 2-5.3 Connecting E1 or T1 Lines

      43
    • 2-5.4 Direct Cabling Between Multiple UltraWAVE or WAVEXpress Systems

      43
    • 2-5.5 Cabling External BTSs

      44
  • 2-6 Connecting Antennas

    44
    • 2-6.1 Omni 1 TRX (O1) Configuration

      45
    • 2-6.2 Omni 2 TRX (O2) Configuration

      46
    • 2-6.3 Omni 3 TRX (O3) Configuration

      46
    • 2-6.4 Omni 4 TRX (O4) Configuration

      46
    • 2-6.5 Omni 5 TRX (O5) Configuration

      47
    • 2-6.6 Omni 6 TRX (O6) Configuration

      48
    • 2-6.7 Omni 5 (05) and Omni 6 (O6) 25 Watt Configuration

      48
    • 2-6.8 Sectorized Two TRX (S11) Configuration

      49
    • 2-6.9 Sectorized Three TRX (S111) Configuration

      49
    • 2-6.10 Two Sector Four TRX (S22) Configuration

      50
    • 2-6.11 Three Sector Four TRX (S211) Configuration

      50
    • 2-6.12 Three Sector Five TRX (S221) Configuration

      51
    • 2-6.13 Three Sector Six TRX (S222) Configuration

      51
    • 2-6.14 Two Sector Five TRX (S32) Configuration

      52
    • 2-6.15 Two Sector Six TRX (S33) Configuration

      52
    • 2-6.16 Two Sector Six TRX (S42) Configuration

      53
    • 2-6.17 RF Radiation Hazard

      53
  • 2-7 Connecting External Alarms

    55
  • 2-8 Post Installation Cabling and Checks

    58
• Three - Off-Line Commissioning

  59
  • 3-1 Pre Off-Line Commissioning

    60
    • 3-1.1 Visual Inspection

      60
  • 3-2 Off-Line Commissioning the UltraWAVE BTS

    62
    • 3-2.1 Connecting the Craft PC to the ICP Processor Card

      62
    • 3-2.2 Starting XWindows Using the Craft PC

      64
    • 3-2.3 Power-On LED Tests

      65
    • 3-2.4 Establishing Serial Communications with the BTS

      67
    • 3-2.5 Verifying/Changing Boot Parameters

      68
  • 3-3 Software verification using Craft PC

    70
    • 3-3.1 Verifying the Current Software Version and Patch Level

      70
    • 3-3.2 Checking the Flash Version Number

      70
    • 3-3.3 Running E1 or T1 POST Diagnostics

      71
    • 3-3.4 Verifying Telnet Communications with the BTS over Ethernet

      72
    • 3-3.5 Running TRX POST Diagnostics

      73
    • 3-3.6 Reviewing POST Results

      75
    • 3-3.7 Rebooting the BTS after Running POST

      76
    • 3-3.8 Terminating Serial Communications with the BTS

      76
  • 3-4 Exiting XWindows on the Craft PC

    77
  • 3-5 Upgrading the BTS Software Version (Flash)

    78
  • 3-6 Post Off-Line Commissioning

    80
• Four - Off-Line Commissioning of a Daisy Chain

  81
  • 4-1 Prerequisites to Daisy Chaining

    81
  • 4-2 Setting the Abis LAPD Signaling Timeslot

    82
• Five - On-Line Commissioning

  83
  • 5-1 Pre On-Line Commissioning Requirements

    84
  • 5-2 On-Line Commissioning

    85
  • 5-3 Antenna Cabling and Power Verification

    90
    • 5-3.1 Voltage Standing Wave Ratio (VSWR) Check

      90
    • 5-3.2 Verifying BTS RF Performance without Racal

      90
    • 5-3.3 Verifying TRX Output Power

      90
    • 5-3.4 RX BER Measurements

      91
  • 5-4 Post On-Line Commissioning Procedures

    93
• Checklist 1 - Site Readiness Checklist

  95
• Checklist 2 - Installation Checklist

  97
• Checklist 3 - Commissioning Checklist

  99