Manuale UtenteSommarioCisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide1Contents3Preface7Audience7Purpose7Organization7Conventions8Related Publications8Obtaining Documentation, Obtaining Support, and Security Guidelines9Product Overview11Switch Module Features Overview11Other Features13Switch Module Console Port1310/100/1000 Ports1410-Gigabit Ethernet Module Slots14Cisco TwinGig Converter Module14LEDs15System LED15Stack LED15Stack Master LED16Stack Member LED16UID and Health LEDs16RJ-45 Uplink Port LEDs1610-Gigabit Ethernet Module Slot Port LEDs17StackWise Plus Ports18Power Connectors18Management Options18Using the Device Manager19Using the Command-Line Interface20Using the Onboard Administrator CLI and GUI20Other Management Options20Network Configurations20Switch Installation21Preparing for Installation21Safety Warnings22Installation Guidelines23Verifying Package Contents24HP c-Class BladeSystem Enclosure Architecture25Installing the Switch Module in the Blade Enclosure26Switch Module IP Addresses28Using the Onboard Administrator to Assign an IP Address to the Switch Module and Running Express Setup29Using Express Setup31Setting the Installed Switch Module As the Stack Master32Refreshing the PC IP Address33Planning and Creating a Switch Stack33Stack Cabling Configurations34Connecting to the StackWise Plus Ports36Installing Devices in the 10-Gigabit Ethernet Slots37Installing X2 Transceiver Modules and Cisco Converter Modules38Installing a Transceiver or Converter Module38Removing a Module39Installing SFP Modules40Installing an SFP Module40Removing an SFP Module41Connecting to the 10/100/1000 Ports42Planning 10/100/1000 Ethernet Port Connections43Where to Go Next44Troubleshooting46Diagnosing Problems46Verify the Switch Module POST Results46Look at the Switch Module LEDs47Confirm the Switch Module Connections47Bad or Damaged Cable47Ethernet and Fiber Cables47Link Status47SFP Module Port Issues48Port and Interface Settings48Ping the End Device48Spanning Tree Loops48Verify the Switch Module Performance49Speed, Duplex, and Autonegotiation49Autonegotiation and Network-Interface Cards49Cabling Distance49Clearing the Switch Module IP Address and Configuration50Replacing a Failed Stack Member50Locating the Switch Module Serial Number51Technical Specifications53Connector and Cable Specifications55Connector Specifications5510/100/1000 Ports55Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices56Connecting to 1000BASE-T Devices5610-Gigabit Ethernet Module Interfaces57Cisco TwinGig Converter Module Ports57Console Port58Cable and Adapter Specifications5810-Gigabit Ethernet X2 Transceiver Module Cable Specifications58SFP Module Cable Specifications60Two Twisted-Pair Cable Pinouts60Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports61Identifying a Crossover Cable62Console Port Adapter Pinouts62Configuring the Switch with the CLI-Based Setup Program65Accessing the CLI Through the Console Port65Connecting to the Console Port65Completing the Initial Configuration68Index71Dimensioni: 3,15 MBPagine: 76Language: EnglishApri il manuale
Manuale UtenteSommarioContents3Preface7Audience7Organization8Related Documentation8Conventions9Obtaining Documentation14Cisco.com14Product Documentation DVD14Ordering Documentation15Documentation Feedback15CiscoProduct Security Overview15Reporting Security Problems in CiscoProducts16Product Alerts and Field Notices16Obtaining Technical Assistance17CiscoTechnical Support & Documentation Website17Submitting a Service Request18Definitions of Service Request Severity18Obtaining Additional Publications and Information18Product Overview21Introduction21System Hardware Features22Front Panel Features22Rear Panel Features23Ports and Connectors23Ethernet Connectors24RJ-45 Cables25Console Port26RJ-45 to DB-9 or DB-25 Adapter27Preparing for Installation29Safety29Warnings and Cautions29General Precautions32Maintaining Safety with Electricity32Protecting Against Electrostatic Discharge33Preparing Your Site for Installation34Environmental Requirements35Choosing a Site for Installation35Ensuring Overcurrent Protection35Grounding the AVS 312035Creating a Safe Environment36AC Power Requirements36Power Supply Guidelines36Cabling36Precautions for Rack-Mounting37Precautions for Products with Modems, Telecommunications, or Local Area Network Options38Required Tools and Equipment38Installing the AVS 312039Unpacking and Inspecting the AVS 312040If the Product is Damaged40Installing Your AVS 312040Attaching a Two-Post Rack Bracket to the AVS 312041Installing the AVS 3120 on a Workbench or Tabletop43Connecting Cables44Connecting AC Power45Booting the AVS 312046Booting with a Console Connected46Establishing a Serial Console Connection47Configuring Network Settings48Setting the Time50Checking the Front Panel LEDs51Removing or Replacing an AVS 312052Troubleshooting the AVS 3120 Hardware53Checking the Basics53Checking Connections54Maintaining Your AVS 312055Maintaining Your Site Environment55Temperature56Humidity56Altitude56Dust and Particles57Corrosion57Electrostatic Discharge57Electromagnetic and Radio Frequency Interference57Power Source Interruptions58Using Power Protection Devices59Surge Protectors59Line Conditioners59Uninterruptible Power Supplies59Specifications61Open Source License Files63Apache License63Index67Dimensioni: 1,99 MBPagine: 70Language: EnglishApri il manuale
