Manuali utente per Pelco C493M-G

Sommario

• Contents

  3
  • List of Tables

    3
• Important Safeguards and Warnings

  4
  • 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

    4
  • 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.

    4
  • 3. Only use replacement parts recommended by Pelco.

    4
  • 4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry.

    4
  • 5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and lens combination.

    4
  • 6. The camera and lens combination shall not exceed 20 lbs (9.09 kg).

    4
• Description

  5
  • Models

    5
  • Options

    5
• Installation

  6
  • Ceiling Mounting (Flush)

    6
    • 1. Remove the cover from the mounting bracket. A special socket is provided (fits 1/4" square drive).

      6
    • 2. Using the mounting bracket (see Figure 4) or the template provided, mark and drill holes in the mounting surface.

      6
    • 3. Attach the enclosure with the required fasteners.

      6
    • 4. Route the required cables through the back and/or top.

      6
    • 5. Mount the camera/lens to the tilt table.

      6
    • 6. Make all appropriate connections (i.e., camera power, video (coax), lens).

      6
    • 7. Position the camera and tighten the 1/4-20 fasteners to secure the tilt table in place.

      6
    • 8. Replace the cover and check that all components clear. Secure the cover with the 1/4-20 “Tampruf” screw provided.

      6
  • Mid-wall Mounting

    6
    • Figure 1. HS1500H Installation

      6
      • 1. Determine the position for the hood. Using it as a template, mark and drill holes in the mounting surface.

        6
      • 2. Attach the hood with the required fasteners (minimum 3/8" diameter recommended).

        6
      • 3. Continue with steps 1-8 listed above in Ceiling Mounting section.

        6
  • HB1500/HB1524 Heater/Blower Kit

    9
    • Recommended Cable Size

      9
    • Heater/Blower Kit Installation

      10
      • 1. Remove the cover (Figure 5, item 4).

        10
      • 2. Attach the heater pads to each side of the mounting frame, below the tilt table assembly.

        10
      • 3. Attach the PC board/fan assembly to the mounting frame, to the left or right of the tilt table assembly (see Figure 2).

        10
      • 4. The blower is factory wired to the PCB assembly.

        10
      • 5. Close and lock the cover.

        10
      • Figure 2. Heather/Blower Installation

        10
      • Figure 3. Heater/Blower Wiring Diagram

        10
  • Tamper Switch installation

    11
    • 1. Remove the front cover.

      11
    • 2. Install the bracket/switch and secure with lockwashers and nuts.

      11
  • Tamper Switch Wiring

    11
    • Figure 4. Tamper Switch Installation

      11
  • Maintenance

    11
• Exploded Assembly Diagram

  12
  • Figure 5. HS1500 Enclosure Exploded Assembly Diagram

    12
  • Table A. HS1500 Enclosure Exploded Assembly Parts Lists

    12
• Specifications

  13
  • MECHANICAL

    13
  • ELECTRICAL

    13
  • GENERAL

    13
    • Figure 6. HS1500 Enclosure Dimension Drawing

      13