Manuali utente per Roberts Gorden BH-200

Sommario

• SECTION 1: Heater Safety

  1
• SECTION 9: Gas Piping

  41
• 1.1 Manpower Requirements

  1
• SECTION 10: Wiring

  43
• 1.2 Safety Labels and Their Placement

  1
• 10.1 Line Voltage Thermostat Wiring

  43
• SECTION 2: Installer Responsibility

  3
• 10.2 Low Voltage Thermostat Wiring

  44
• 2.1 Wall Tag

  3
• 10.3 Internal Wiring

  45
• 2.2 Corrosive Chemicals

  3
• 10.4 Ladder Diagram

  46
• 2.3 National Standards and Applicable Codes

  3
• 10.5 Electrical Connection to the Burner

  46
• SECTION 3: Clearances to Combustibles

  4
• SECTION 11: Operation and Maintenance

  47
• 3.1 Required Clearances to Combustibles

  4
• 11.1 Sequence of Operation

  47
• SECTION 4: National Standards and Applicable Codes

  9
• 11.2 To Shut Off Heater

  47
• 4.1 Gas Codes

  9
• 11.3 To Start Heater

  47
• 4.2 Aircraft Hangars

  9
• 11.4 Pre-Season Maintenance and Annual Inspection

  47
• 4.3 Public Garages

  9
• 11.5 Maintenance Checklist

  49
• 4.4 Electrical

  9
• 4.5 Venting

  9
• 12.1 Troubleshooting Flow Chart

  52
• 4.6 High Altitude

  9
• 12.2 Manifold Gas Pressure Setting

  54
• SECTION 5: Major Components

  10
• SECTION 13: Replacement Parts

  55
• 5.1 Standard Parts List

  11
• SECTION 14: General Specifications

  58
• SECTION 6: Heater Installation

  13
• 14.1 Material Specifications

  58
• 6.1 Burner Tube Installation

  17
• 14.2 Heater Specifications

  58
• 6.2 Tube Clamp Package Installation

  18
• 14.3 Suspension Specifications

  58
• 6.3 Coupling and Tube Assembly

  18
• 14.4 Controls Specifications

  58
• 6.4 Turbulator Installation

  20
• 6.5 Reflector Installation

  21
• Warranty

  59
• 6.6 Burner Installation

  23
• SECTION 7: Optional Heater Accessories

  24
• 7.1 U-Tube Configuration

  24
• 7.2 Elbow Package Configuration

  27
• 7.3 Reflector Side Extension

  30
• 7.4 Lower Clearance Shield Installation

  31
• 7.5 Two-Foot Decorative Grille Installation

  31
• 7.6 Protective Grille Installation

  33
• SECTION 8: Venting

  34
• 8.1 Venting

  34
• 8.2 Unvented Operation

  35
• 8.3 Horizontal Venting

  35
• 8.4 Vertical Venting

  35
• 8.5 Unvented Operation Tube Termination

  35
• 8.6 Length Requirements

  35
• 8.7 Horizontal Ventilation 4'' (10 cm) Pipe

  36
• 8.8 Vertical Ventilation 4'' (10 cm) Pipe

  36
• 8.9 Common Side Wall Venting

  37
• 8.10 Common Vertical Venting

  38
• 8.11 Outside Combustion Air Supply

  39
• Figure 1: Top and Bottom Panel Label Placement

  1
• Figure 2: Side and Back Panel Label Placement

  2
• Figure 3: Standard Reflector

  5
• Figure 4: One Side Reflector

  5
• Figure 5: Two Side Reflectors

  5
• Figure 6: 45° Tilt Reflector

  6
• Figure 7: U-Tube, Standard Reflector

  6
• Figure 8: U-Tube, 45°

  6
• Figure 9: U-Tube, Opposite 45° Reflector

  7
• Figure 10: 2-Foot Deco Grille and Protective Grille

  7
• Figure 11: Lower Clearance Shield

  7
• Figure 12: Venting

  8
• Figure 13: Major Component Descriptions

  10
• Figure 14: Critical Hanger Placement

  14
• Figure 15: Linear Heater Assembly Overview

  15
• Figure 16: Linear Heater Layout Overview

  16
• Figure 17: Linear Heater Layout Overview (Continued)

  17
• Figure 18: U-Tube Heater Assembly Overview

  25
• Figure 19: U-Tube Heater Layout Overview

  26
• Figure 20: U-Tube Layout Overview (Continued)

  27
• Figure 21: Reflector Joint Detail

  29
• Figure 22: Tube Termination

  35
• Figure 23: Gas Connection with Flexible Gas Hose

  42
• Table 1: Contents of BH-Series Burner Carton

  11
• Table 2: Contents of Core and Extension Packages

  11
• Table 3: BH-Series Component Package Guide

  12