Manuali utente per Tandberg Data Data Network Router MSE 8321

Sommario

• Table of contents

  4
• General information

  5
  • About the ISDN gateway

    5
  • Port and LED location

    5
    • Figure 1: ISDN gateway front panel

      5
  • LED behavior

    6
    • Table 1: ISDN gateway LED behavior

      6
• Installing the ISDN gateway

  8
  • Install the ISDN gateway into the MSE 8000 chassis

    8
    • 1 Remove the blade or blanking blade from the slot into which you are going to install the ISDN gateway:

      8
      • i Using a No.1 Phillips screwdriver, loosen the screws in the retaining latches with an anti-clockwise quarter turn.

        8
      • ii Open both retaining latches on the front of the blade or blanking blade. When open, a retaining latch is at a 90 angle perpendicular to the front of the blade.

        8
      • iii Slide out the blade or blanking blade.

        8
      • 2 Open both retaining latches on the front of the ISDN gateway. When open, a retaining latch is at a 90 angle perpendicular to the front of the blade.

        8
      • 3 Slide the ISDN gateway into the blade slot (as shown in Figure 2) until it stops.

        8
      • 4 Simultaneously close both retaining latches on the blade (thereby engaging the connectors at the rear of the blade) to secure in the chassis as shown in Figure 3.

        8
      • 5 Using a No.1 Phillips screwdriver, tighten the screws in the retaining latches with a clockwise quarter turn.

        9
        • Figure 2: Inserting a blade into the chassis

          9
        • Figure 3: Closing the retaining latches on the front of a blade

          9
• Connecting the ISDN gateway

  10
  • Your ISDN connection

    10
    • Outside North America

      10
    • Within North America

      10
  • Step one: Connect to Ethernet Port A

    10
  • Step two: Connect to the ISDN ports

    10
• Initial configuration

  11
  • Step one: Configure Ethernet Port A settings

    11
  • Step two: Assign an IP address to the ISDN gateway

    11
• Configuring the ISDN gateway

  12
  • Step one: Log in to the ISDN gateway

    12
    • 1 Log in to the Supervisor’s web interface.

      12
      • 2 Go to Hardware > Blades and click the IP address of the ISDN gateway.

        12
      • 3 Click Click here to log in, and then click Change log in and enter the user name admin with no password.

        12
  • Step two: Set up the ISDN interfaces

    12
    • 1 In the web interface, go to Settings > ISDN.

      12
      • 2 Select the ISDN interface type to match that of your installation; E1 is typically used in the UK and mainland Europe, T1 (USA and Canada) in North America, and T1(Japan) in Japan.

        12
      • 3 Complete the other settings as required by your network, referring to the online help for further information.

        12
      • 4 Click Apply changes to save any changes you have made to the configuration.

        12
      • 5 Restart the ISDN gateway (this is only necessary if you changed the ISDN configuration). To do this:

        12
        • i Go to Settings > Shutdown, and click Shut down ISDN GW.

          12
        • ii Confirm that you want to shut down the ISDN gateway.

          12
        • iii Click Restart ISDN GW.

          12
      • 6 When the ISDN gateway has restarted, log in to the web interface again, and go to Settings > ISDN ports.

        12
      • 7 Complete the settings for ISDN Port 1 as required by your network, referring to the online help for further information. Note that all ISDN ports on the ISDN gateway are enabled by default.

        12
      • 8 Click Apply changes to save your configuration changes to the ISDN port.

        12
      • 9 If required, configure another ISDN port by selecting the port number from the numbered links at the top right of the ISDN port configuration page.

        12
  • Step three: Configure an H.323 gatekeeper

    13
  • Step four: Configure the dial plan

    13
    • 1 In the web interface, go to Dial plan > IP to ISDN and click Add rule.

      13
      • 2 For Condition, select Match any called number.

        13
      • 3 For Action, select Call with the original called number.

        13
      • 4 Leave the other values unchanged. Click Add rule to add the rule to the dial plan.

        13
      • 5 Now go to Dial plan > ISDN to IP, and click Add rule.

        13
      • 6 For Condition, select Match any called number.

        13
      • 7 For Action, select Call this number and enter the IP address of your MCU.

        13
      • 8 Leave the other values unchanged. Click Add rule to add the rule to the dial plan.

        13
• Configuring the MCU

  14
  • Adding the ISDN gateway

    14
    • 1 Using your web browser, navigate to the web interface of the MCU.

      14
      • 2 Go to Gateways.

        14
      • 3 Click Add new H.323 gateway.

        14
      • 4 Enter a name for the gateway, such as Codian ISDN gateway, and specify the IP address of the ISDN gateway. Leave all other fields unchanged.

        14
      • 5 Click Add H.323 gateway.

        14
  • Configuring endpoints

    14
    • 1 Using your web browser, navigate to the web interface of the MCU.

      14
      • 2 Go to Endpoints.

        14
      • 3 Click Add H.323.

        14
      • 4 Enter a name for the endpoint, such as CEO ISDN phone.

        14
      • 5 In the Address field, type the phone number of the endpoint.

        14
      • 6 Select the gateway you have just added for H.323 gateway. Leave all other fields unchanged.

        14
      • 7 Click Add endpoint.

        14
• Making calls

  15
  • Calling in by ISDN

    15
  • Calling out by ISDN

    15
    • 1 Using your web browser, navigate to the web interface of the MCU.

      15
      • 2 Go to Conferences and select the conference you are interested in by clicking its name.

        15
      • 3 Click Add participant and select the ISDN endpoint from the list of pre- configured endpoints. Click Add selected.

        15
• Troubleshooting and technical support information

  16
  • Calls fail to complete

    16
  • Using the event log to help solve a problem

    16
  • Getting more help

    17
    • 1 Refer to the Technical FAQ section of the web site. We keep the Technical FAQ section up to date with the latest information from our technical support team regarding the resolution of customer issues.

      17
      • 2 Contact your reseller. Our resellers have a wealth of experience with our products and this is sometimes a quick way of solving a problem.

        17
      • 3 If your query remains unsolved, there is a web form in the Support area of the web site that you can complete. Ensure that you provide all the details requested by the form to assist the technical support team in resolving your problem:

        17
• Pin outs

  18
  • Table 2: Pin assignments for PRI ports

    18
  • Figure 4: Pin numbering for PRI ports

    18