Manuali utente per Teledyne 3020T

Sommario

• 1.1 Overview

  1
• 1.2 Typical Applications

  1
• 1.3 Main Features of the Analyzer

  1
• 1.4 Model Designations

  1
• 1.5 Operator Interface

  1
• 1.5.1 UP/DOWN Switch

  1
• 1.5.2 ESCAPE/ENTER Switch

  1
• 1.5.3 Displays

  1
• 1.6 Recognizing Difference Between LCD & VFD

  1
• 1.7 Rear Panel Equipment Interface

  1
• 1.7.1 Electrical Connector Panel

  1
• 1.7.2 Gas Connector Panel

  1
• 2.1 Introduction

  2
• 2.2 Micro-Fuel Cell Sensor

  2
• 2.2.1 Principles of Operation

  2
• 2.2.2 Anatomy of a Micro-Fuel Cell

  2
• 2.2.3 Electrochemical Reactions

  2
• 2.2.4 The Effect of Pressure

  2
• 2.2.5 Calibration Characteristics

  2
• 2.3 Sample System

  2
• 2.4 Electronics and Signal Processing

  2
• 2.5 Temperature Control

  2
• 3.1 Unpacking the Analyzer

  3
• 3.2 Mounting the Analyzer

  3
• 3.3 Electrical Connections

  3
• 3.3.1 Primary Input Power

  3
• 3.3.2 Fuse Installation

  3
• 3.3.3 Analog Outputs

  3
• 3.3.4 Alarm Relays

  3
• 3.3.5 Digital Remote Cal Inputs

  3
• 3.3.6 Range ID Relays

  3
• 3.3.7 Network I/O

  3
• 3.3.8 RS-232 Port

  3
• 3.3.9 Remote Sensor and Solenoid Valves

  3
• 3.4 Installing the Micro-Fuel Cell

  3
• 3.5 Gas Connections

  3
• 3.6 Testing the System

  3
• 4.1 Introduction

  4
• 4.2 Using the Controls

  4
• 4.2.1 Mode/Function Selection

  4
• 4.2.1.1 Analysis Mode

  4
• 4.2.1.2 Setup Mode

  4
• 4.2.2 Data Entry

  4
• 4.2.2.1 ENTER

  4
• 4.2.2.2 ESCAPE

  4
• 4.3 The AUTO-CAL Function

  4
• 4.4 The PWD Function

  4
• 4.4.1 Entering the Password

  4
• 4.4.2 Installing or Changing the Password

  4
• 4.5 The LOGOUT Function

  4
• 4.6 The VERSION Screen

  4
• 4.7 The SELF TEST Function

  4
• 4.8 The ZERO and SPAN Functions

  4
• 4.8.1 Zero Cal

  4
• 4.8.1.1 Auto Mode Zeroing

  4
• 4.8.1.2 Manual Mode Zeroing

  4
• 4.8.1.3 Cell Failure

  4
• 4.8.2 Span Cal

  4
• 4.8.2.1 Auto Mode Spanning

  4
• 4.8.2.2 Manual Mode Spanning

  4
• 4.9 The ALARMS Function

  4
• 4.10 The RANGE Function

  4
• 4.10.1 Setting the Analog Output Ranges

  4
• 4.10.2 Fixed Range Analysis

  4
• 4.11 The CONTRAST Function

  4
• 4.12 The STANDBY Function

  4
• 4.13 The Analysis Mode

  4
• 5.1 Routine Maintenance

  5
• 5.2 Major Internal Components

  5
• 5.3 Cell Replacement

  5
• 5.3.1 Storing and Handling Replacement Cells

  5
• 5.3.2 When to Replace a Cell

  5
• 5.3.3 Removing the Micro-Fuel Cell

  5
• 5.3.4 Installing a New Micro-Fuel Cell

  5
• 5.2.5 Cell Warranty

  5
• 5.4 Fuse Replacement

  5
• 5.5 System Self Diagnostic Test

  5