Manuali utente per Viewsonic VS13646

Sommario

• Introduction

  7
  • Projector Features

    7
  • Package Contents

    8
• Projector with Lens Cap

  8
• AC Power Cord

  8
  • Projector Overview

    10
• Front View

  10
• Rear View

  11
• Bottom View

  11
  • Using the Product

    12
    • Control Panel

      12
    • Connection Ports

      13
    • Remote Control

      15
• Using the remote mouse control

  16
  • 1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See “Connecting a computer” on page 18 for details.

    16
  • 2. Set the input signal to Computer in 1 or Computer in 2.

    16
  • 3. Press Mouse on the remote control to switch from the normal mode to the mouse mode. An icon appears on the screen to indicate the activation of the mouse mode.

    16
  • 4. Perform the desired mouse controls on your remote control.

    16
  • Installing the Batteries

    17
    • 5. Open the battery cover in the direction shown.

      17
    • 6. Install batteries as indicated by the diagram inside the compartment.

      17
    • 7. Close the battery cover into position.

      17
  • Remote Control Operation

    18
  • Connection

    19
    • 1. Turn all equipment off before making any connections.

      19
    • 2. Use the correct signal cables for each source.

      19
    • 3. Ensure the cables are firmly inserted.

      19
    • Connecting a computer or monitor

      20
• Connecting a computer

  20
  • 1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.

    20
  • 2. Connect the other end of the VGA cable to the Computer in 1 or Computer in 2 signal input socket on the projector.

    20
  • 3. If you wish to use the remote paging function, take a USB cable and connect the A type end to the USB port of the computer, and the other end to the Service socket on the projector. See “Using the remote mouse control” on page 14 for details.

    20
• Connecting a monitor

  20
  • 1. Connect the projector to a computer as described in “Connecting a computer” on page 18.

    20
  • 2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor.

    20
  • 3. Connect the other end of the cable to the Monitor Out socket on the projector.

    20
  • Connecting Video source devices

    21
• Connecting a Component Video source device

  22
  • 1. Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a Component Video to VGA (D-Sub) adaptor and connect the end...

    22
  • 2. If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video to VGA (D-Sub) adaptor, connect the other end of...

    22
• Connecting an S-Video source device

  22
  • 1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

    22
  • 2. Connect the other end of the S-Video cable to the S-Video socket on the projector.

    22
• Connecting a composite Video source device

  23
  • 1. Take a Video cable and connect one end to the composite Video output socket of the Video source device.

    23
  • 2. Connect the other end of the Video cable to the Video socket on the projector.

    23
  • Operation

    24
    • Powering On/Off the Projector

      24
• Powering On the Projector:

  24
  • 1. Remove the projector lens cap.

    24
  • 2. Complete the AC power cord and peripheral signal cable(s) connections.

    24
  • 3. Press to turn on the projector. The projector takes a minute or so to warm up.

    24
  • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.

    24
• Powering Off the Projector:

  24
  • 1. Press to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.

    24
  • 2. Press again to confirm.

    24
  • 3. Disconnect the AC power cord from the electrical outlet and the projector.

    24
  • 4. Do not turn on the projector right after power off.

    24
  • Adjusting the Projector Height

    25
    • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.

      25
    • 2. To level the image on the screen, turn the tilt-adjustment feet to fine-tune the height.

      25
  • Adjusting the Projector Zoom and Focus

    25
    • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.

      25
    • 2. Adjust the image size by sliding the zoom ring.

      25
  • Adjusting Projection Image Size

    26
  • Locking control keys

    27
    • 1. Press on the projector or remote control.

      27
    • 2. A confirmation message is displayed. Select Yes to confirm.

      27
  • Creating your own startup screen

    27
    • 1. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the Option menu is highlighted.

      27
    • 2. Press to highlight Start up Screen and press MODE/ENTER on the projector or Enter on the remote control.

      27
    • 3. A confirmation message is displayed. Press MODE/ENTER on the projector or Enter on the remote control again.

      27
    • 4. The message 'Screen Capturing...' is displayed while the projector is processing the picture. Please wait.

      27
    • 5. If the action is successful, you see the message 'Capture Succeeded' on the screen. The captured picture is saved as User.

      27
    • 6. To view the captured picture displayed as the startup screen, set User in the Option > Start up Screen > User menu and restart the projector.

      27
  • Setting the presentation timer

    28
    • 1. Go to the Setting > Presentation Timer menu and press MODE/ENTER to display the Presentation Timer page.

      28
    • 2. Highlight Timer Period and decide the timer period by pressing /. The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-minute increments.

      28
    • 3. Press to highlight Timer Display and choose if you want the timer to show up on the screen by pressing / .

      28
    • 4. Press to highlight Timer Position and set the timer position by pressing / .

      28
    • 5. Press to highlight Timer Counting Direction and select your desired counting direction by pressing/.

      28
    • 6. To activate the presentation timer, press and press / to select On and press MODE/ENTER.

      28
    • 7. A confirmation message displays. Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting at the time when the timer is on.

      28
• To cancel the timer, perform the following steps:

  29
  • 1. Go to the Setting > Presentation Timer menu and highlight Off.

    29
  • 2. Press MODE/ENTER. A confirmation message displays.

    29
  • 3. Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is Off!” displaying on the screen.

    29
  • Menu Operation

    30
• How to operate

  33
  • 1. Press MENU on the projector or Menu on the remote control to open the OSD menu.

    33
  • 2. When OSD is displayed, use / to select any feature in the main menu.

    33
  • 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.

    33
  • 4. Use / to select the desired item and adjust the settings with /.

    33
  • 5. Press MENU on the projector or Menu on the remote control, the screen will return to the main menu.

    33
  • 6. To exit OSD, Press MENU on the projector or Menu on the remote control again. The OSD menu will close and the projector will automatically save the new settings.

    33
  • Controlling the projector through a LAN environment

    40
• Wired connection

  40
  • 1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router.

    40
  • 2. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the NetWork menu is highlighted.

    40
  • 3. Highlight Wired LAN and press ENTER on the projector or Enter on the remote control.

    40
  • 4. Make sure the Status is Connect.

    40
  • 5. Press to highlight DHCP and press / to select On.

    40
  • 6. Press to highlight Apply and press ENTER on the projector or Enter on the remote control.

    40
  • 7. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row.

    40
  • 1. Repeat steps 1-4 above.

    40
  • 2. Press to highlight DHCP and press / to select Off.

    40
  • 3. Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings.

    40
  • 4. Press to select the item you want to modify and press ENTER on the projector or Enter on the remote control.

    41
  • 5. Press / to move the cursor and the enter the value.

    41
  • 6. To save the settings, press ENTER on the projector or Enter on the remote control. If you do not want to save the settings, press MENU/EXIT on the projector

    41
  • 7. or Menu on the remote control.

    41
  • 8. Press to highlight Apply and press ENTER on the projector or Enter on the remote control.

    41
• Wireless connection

  42
  • 1. Make sure the projector is turned on.

    42
  • 2. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the NetWork menu is highlighted.

    42
  • 3. Highlight Wireless LAN and press ENTER on the projector or Enter on the remote control.

    42
  • 4. Make sure the Status is Connect.

    42
  • 5. Make sure the SSID information is displayed.

    42
  • 6. Press to highlight Connection Mode and press / to select AP or Infrastructure. In AP mode, you need to use your computer’s wi...

    42
  • Controlling the projector through a web browser

    43
    • 1. Enter the address of the projector in the address bar of your browser and press Enter.

      43
    • 2. The main page of the ViewSonic webpage control system appears.

      43
    • 3. To change the language for the web pages, click the down arrow to reveal a drop down list and select a desired language.

      43
    • 4. To download pwPresenter, click Download. See “Displaying images through pwPresenter” on page 47 for details.

      43
    • 5. To achieve best performance, download the install mirror display driver.

      43
    • 6. To download USB LAN driver, click Download.

      43
    • 7. To have access to the Admin page, you need to enter a password. The default password is “0000”.

      44
    • 8. The Crestron (eControl) page displays the Crestron eControl user interface. The eControl page provides a variety of virtual keys to control the projector or adjust the projected pictures.

      45
  • Displaying images through pwPresenter

    49
• Downloading and installing pwPresenter

  49
  • 1. Enter the main page of Network Control. See steps 1-2 on page 41 for details.

    49
  • 2. Download pwPresenter.

    49
  • 3. When the download is complete, install the software to your computer by clicking the exe file. Follow the on-screen instructions to complete the installation.

    49
  • 4. Launch pwPresenter.

    49
• Using pwPresenter

  49
  • 1. The Search page allows you to search and connect to a projector.

    49
  • 2. The Capture screen allows you to start or pause capture screen.

    50
  • 3. You can choose a capture mode from here.

    50
  • 4. The Basic Setting page allows you to configure pwPresenter.

    51
  • 5. The Advanced Setting page allows you to configure pwPresenter.

    52
  • 6. Network Display Management displays the Device Management and pwPresenter Management information.

    53
  • 7. Disconnect allows you to disconnect from the projector(s) by clicking the Disconnect icon.

    54
  • Displaying pictures with a USB storage device

    55
    • 1. Take a USB cable and connect the larger end to the USB A socket on the projector, and smaller end to the USB port of the device. If you are using a USB flash drive, connect it directly to the USB A socket.

      55
    • 2. The projector automatically display the thumbnails. Or your can manually select USB Reader from the source selection bar.

      55
    • 3. The ImageView main screen is displayed and ready to use. The main screen is displayed in Thumbnail Display Mode which shows the following four parts:

      55
    • 4. Use the four directional buttons or page up/down button to move between pages/ folders. To Press and hold Menu and then press...

      55
  • Maintenance

    57
    • Cleaning the Lens

      57
    • Cleaning the Projector Housing

      57
    • Cleaning the Filter Cover

      57
      • 1. Switch the projector off and unplug the AC power cord from the wall socket.

        57
      • 2. Remove the filter cover as the illustration shown.

        57
      • 3. Clean the filter cover.

        57
      • 4. Replace the filter cover.

        57
      • 5. Attach the filter cover.

        57
      • 6. Plug the power back into the projector.

        57
    • Replacing the Lamp

      58
      • 1. Turn off the projector.

        59
      • 2. If the projector is installed in a ceiling mount, remove it

        59
      • 3. Unplug the power cord.

        59
      • 4. Loosen the screw in the side of the lamp cover and remove the cover.

        59
      • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.

        59
      • 6. Insert the new lamp module into the projector and tighten the screws.

        59
      • 7. Replace the lamp cover and tighten the screw.

        59
      • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.

        59
      • 9. Reset the lamp hour. Refer to the “Information” menu.

        59
  • Specifications

    60
    • Dimensions

      61
    • Ceiling mount installation

      61
  • Appendix

    62
    • LED Indicator Messages

      62
    • Compatibility Modes

      63
• Computer:

  63
• Video:

  64
  • Troubleshooting

    65
• Start-up problems

  65
• Image problems

  65
  • IR Control Code

    68