Manuali utente per Zebra Technologies Corporation RFID-Z4M-01

Sommario

• Table of Contents

  5
• Proprietary Statement

  9
  • Product Improvements

    9
  • FCC Compliance Statement

    9
  • Liability Disclaimer

    10
  • Limitation of Liability

    10
  • Copyrights

    10
• Declaration of Conformity

  11
  • Zebra Technologies Corporation

    11
• Warranty Information

  13
  • Printer Products

    13
  • Printer Software and Firmware License Agreement

    15
• Preface

  21
  • Contacts

    22
    • Support

      22
  • About this Document

    23
  • Document Conventions

    24
  • Related Documents

    26
• Introduction

  27
  • External View

    28
  • Front Panel

    29
    • LCD Display Settings

      30
    • Print Modes

      31
  • Printer Media Compartment

    32
• Printer Setup

  33
  • Before You Begin

    34
  • Unpack and Inspect the Printer

    35
    • Report Damage

      35
    • Storage

      35
  • Select a Site for the Printer

    36
    • Select a Surface

      36
    • Provide Proper Operating Conditions

      36
    • Allow Proper Space

      36
    • Provide a Data Source

      36
  • Connect the Printer to a Power Source

    37
    • Power Cord Specifications

      37
  • Select a Communication Interface

    39
    • Cable Requirements

      40
  • Types of Media

    41
    • Non-Continuous Web Media

      41
    • Continuous Media

      42
    • RFID “Smart” Labels

      43
  • Ribbon

    44
• Printer Operation

  45
  • Front Panel

    46
    • Front Panel Keys

      47
    • Front Panel Lights

      48
  • Load Roll Media

    49
    • Tear-Off Mode

      49
    • Peel-Off Mode

      51
    • Liner Take-Up Mode

      53
  • Load Fanfold Media

    60
  • Load the Ribbon

    62
    • Remove the Ribbon

      63
  • Calibrate the Printer

    64
    • Auto Calibration

      64
    • Manual Calibration

      64
  • Print a Configuration Label

    65
  • Adjust Printhead Pressure

    67
  • Install Memory Card

    68
• Configuration

  69
  • Overview

    70
    • Enter Configuration Mode

      70
    • Exit Configuration Mode

      70
    • Change Password-Protected Parameters

      71
  • Basic Configuration

    72
  • Configuration and Calibration LCD Displays

    75
• RFID Guidelines

  95
  • Overview

    96
  • Transponder Placement

    96
  • ZPL II Commands for RFID

    97
    • ^WT

      98
    • ^RT

      99
    • ^HV

      100
    • ^RS

      101
  • Sample of RFID Programming

    105
• Routine Care and Adjustments

  107
  • Cleaning Procedures

    108
    • Clean the Exterior

      108
    • Clean the Interior

      109
    • Clean the Sensors

      110
    • Clean the Rewind Option

      111
    • Clean the Peel-Off Assembly

      112
  • Lubrication

    113
  • Fuse Replacement

    113
• Troubleshooting

  115
  • LCD Error Conditions and Warnings

    116
  • Print Quality Problems

    118
  • Calibration Problems

    119
  • Communication Problems

    120
  • Printer Diagnostics

    121
    • Power-On Self Test

      121
    • Cancel Self Test

      122
    • Pause Self Test

      123
    • Feed Self Test

      124
    • Communications Diagnostics Test

      125
    • RFID Test

      126
  • Loading Factory Defaults

    127
• Data Connections

  129
  • Serial Data Port

    130
    • Hardware Control Signal Descriptions

      130
    • RS-232 Serial Data Port

      130
  • Parallel Data Port

    134
    • Parallel Cabling Requirements

      134
    • Parallel Port Interconnections

      134
• Specifications

  135
  • General Specifications

    136
  • Printing Specifications

    137
  • Media Specifications

    138
  • Ribbon Specifications

    140
  • Printer Options

    141
  • Zebra Programming Language (ZPL II) Features

    142
  • Supported Bar Codes

    142
• Index

  143