Marantz RC101 ユーザーズマニュアル

This remote controller is capable of learning and 
storing codes used by other remote controls that you 
already own.
For codes which are not learned, the remote 
controller will transmit either the Marantz preset 
codes from the initial settings, or remote codes from 
another manufacturer’s AV equipment which is set 
by the customer.
The receiver sensor for the remote control signals is 
located at the top of the remote controller.

•  This remote controller is capable to learn around 60 

codes.

• When the batteries are getting weak , the learing 

procedure is not successful.

 

  Place the remote controller so that its infrared 

signal transmitter is facing the infrared signal 
receiver on the Marantz remote controller at a 
distance of about 2 inches (0.05 m).

2 inches

 

  Press and hold down the 

 and 

 buttons until LEARN indicator blinks.

 

 Select 

the 

 button to select the 

SOURCE.

 

  Select the button to be learned.

•  LEARN indicator lights up.

• 

 buttons

 

  The learning function is unavailable for all 

SOURCE buttons in any mode.

• 

 button 

• 

 button 

• 

 button 

• 

 button 

• 

 button 

• 

 button 

 

  The above keys are common use in each 

device mode. It can be learned in TV mode.

 

  Press and hold the button of the original remote 

controller to learn until the SEND indicator 
blinks twice.

•  When the SEND indicator blinks once, 

repeat this step.

•  When the memory of the RC101 is full, the 

LEARN and SEND indicators blink once. 
If you want to learn the code, you should 
erase other learned button.

 Repeat 

steps 

 and 

 to learn other buttons in 

same SOURCE.

 

 Repeat 

steps 

 to 

 to learn other SOURCE.

 

  When you have finished programming the 

remote controller, press the 

 button, then 

LEARN indicator stops blinking and exits from 
the LEARN mode.

• When the SEND indicator blinks once again, the 

transmitting code is unavailable for RC101, or the 
transmitting signal is intercepted by noise.

• If no buttons are pressed for approximately 1 

minutes while in the LEARN mode, the remote 
controller automatically exits from the LEARN 
mode.

Codes can be erased in three ways: by buttons, 
sources, and by all memory contents.

 

  Press and hold down the 

 and 

 buttons until LEARN indicator blinks.

 

 Select 

the 

 button to select the button 

to be erased.

 

  Press and hold down the 

 button and 

press the learned button twice to be erased.

•  SEND indicator blinks twice and the mode 

returns to LEARN mode.

 

  To return the NORMAL mode, press the 

 

button.

 

  Press and hold down the 

 and 

 buttons until LEARN indicator blinks.

 

  Press and hold down the 

 button and 

press the learned 

 button twice to be 

erased.

•  LEARN indicator lights.

 

 Press 

 button to continue erasing.

•  The SEND indicator blinks twice and the 

mode returns to LEARN mode.

•  To cancel the erasing operation, do not 

press 

button and simply touch any 

other button.

 

  To return the NORMAL mode, press the 

 

button.

 

  Press and hold down the 

 and 

 buttons until LEARN indicator blinks.

 

  Press and hold down the 

 button and 

press 

 and 

 button.

•  LEARN indicator lights.

 

 Press 

 button to continue erasing.

•  The SEND indicator blinks twice and the 

mode returns to LEARN mode.

•  To cancel the erasing operation, do not 

press 

button and simply touch any 

other button.

 

  To return the NORMAL mode, press the 

 

button.

Erasing codes will return to the factory preset code, 
or there will leave empty if the button has no factory 
preset code.