Panasonic AJ-HD1700PE ユーザーズマニュアル

Setup menus

The underlining (__) denotes the factory setting mode.

<EDIT>

No./Item

Description of setting

300

IN/OUT DEL

For selecting the operation to be performed when
an edit point has been set incorrectly (when the
OUT point comes before the IN point).

0000

MANU:

Editing is not performed unless the illegal edit
point is cleared or set properly.

0001

AUTO:

The edit point which had already been input is
cleared automatically.

301

NEGA FLASH

For selecting whether to show a negative display
(time code display area) when the IN point is
greater than the OUT point.

0000

OFF:

A negative display is not shown.

0001

ON:

A negative display is shown.

No./Item

Description of setting

302

CONFI EDIT

For selecting whether to perform simultaneous
playback during editing.

0000

OFF:

Simultaneous playback is not
performed.

0001

ON:

Simultaneous

playback

performed.

<Note>
Simultaneous playback takes effect when TAPE is
selected as the F1 key

setting on the

<HOME> menu. Refer to setup menu item No.140 as
well.

OUTPUT

303*

AUD EDIT
IN

For selecting how to connect the digital audio
edit IN points.

0000

CUT:

Cut processing

0001

FADE:

V-fade processing

304*

AUD EDIT
OUT

For selecting how to connect the digital audio
edit OUT points.

0000

CUT:

Cut processing

0001

FADE:

V-fade processing

305

AUTO ENTRY

For selecting whether to register the IN points
using the PREROLL button in cases where
the IN points have not been registered.

0000

DIS:

The

points

are

not

registered.

0001

ENA:

The IN points are registered.

306*

CF ADJ SEL

For selecting the deck whose the color
framing is to be adjusted during deck-to-deck
editing.

0000 PLAYER:

The player’s IN and OUT points are adjusted
(using the recorder as the reference).

0001 RECORD:

The recorder’s IN and OUT points are adjusted
(using the player as the reference).

307

AFTER
CUE-UP

For selecting the VTR’s mode upon
completion of the cue-up operation.

0000

STOP:

The VTR is set to the STOP mode.

0001

STILL:

The VTR is set to the still picture (SHTL STILL)
mode.

0002

STILL2:

The VTR is set to the still picture (VAR STILL)
mode.

308

VAR FWD
MAX

For setting the maximum speed of VAR FWD.

0000

4.9:

4.9 times normal tape speed

0001

2 times normal tape speed

(

1.85 times normal tape

speed for formats other than
DVCPRO HD-LP)

0002

1 times normal tape speed

<Notes>
• At any setting other than 0 (

4.9), phase adjustments

cannot be conducted from the editing controller.

• Depending on the format used, the actual tape

running speed differs slightly from what is indicated
by the superimposed display.

310

JOG FWD
MAX

For setting the maximum speed of JOG FWD.

0000

4.9:

4.9 times normal tape speed

0001

2 times normal tape speed

(

1.85 times normal tape

speed for formats other than
DVCPRO HD-LP)

0002

1 times normal tape speed

<Notes>
At any setting other than 0 (

4.9), phase adjustments

cannot be conducted from the editing controller which
performs these adjustments by the JOG command.

311

JOG REV MAX

For setting the maximum speed of JOG REV.

0000

4.9:

4.9 times normal tape speed

0001

2 times normal tape speed

(

1.85 times normal tape

speed for formats other than
DVCPRO HD-LP)

0002

1 times normal tape speed

312

POSTROLL
TM

For setting the postroll time.
Any time from 0 to 5 seconds can be set in 1-
second increments.

0000

0001

0002

0003

0004

0005

309

VAR REV MAX

For setting the maximum speed of VAR REV.

0000

4.9:

4.9 times normal tape speed

0001

2 times normal tape speed

(

1.85 times normal tape

speed for formats other than
DVCPRO HD-LP)

0002

1 times normal tape speed

<Note>
Depending on the format used, the actual tape running
speed differs slightly from what is indicated by the
superimposed display

*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or

SD) mode has been selected as the system menu item No.25
(SYSTEM FREQ) setting.