Philips VR530/07 ユーザーズマニュアル

This apparatus is fitted with an approved moulded 10
Amp plug. To change a fuse in this type of plug pro-
ceed as follows:

1.Remove fuse cover and fuse.

2.Fix new fuse which should be a 

BS1362 3A,ASTA or BSI approved type.

3.Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted in its
place.
If the mains plug contains a fuse, this should have a
value of 3A. If a plug without a fuse is used, the fuse at
the distribution board should not be greater than 3A.

How to connect a plug:
The wires in the mains lead are coloured in accor-
dance with the following code:
BLUE- 'NEUTRAL' ('N')
BROWN- 'LIVE' ('L')

4.The BLUE wire must be connected to the terminal

which is marked with the letter 'N' or coloured
BLACK.

5.The BROWN wire must be connected to the termi-

nal which is marked with the letter 'L' or coloured
RED.

6.Do not connect either wires to the earth terminai in

the plug which is marked with the letter 'E' or by
the safety earth symbol 

or coloured green or

green-and-yellow.

Before replacing the plug cover, make certain that the
cord grip is clamped over the sheath of the lead-not
imply over the two wires.

The remote control and its
batteries are packed sepa-
rately in the original video
recorder packaging. You must install the batteries in the
remote control before use.

1.Take the remote control and the enclosed batteries

(2 batteries).

2.Open the remote control's battery compartment

and place the batteries in it as shown in the picture
and close the battery compartment.

The remote control is now ready to use. Its range is
approximately 5 metres.

The necessary cable connections
must be made before you can
record or playback TV programmes
using your video recorder.
We recommend that you use a scart cable to connect
your TV and video recorder.

Have the following cables ready:
an aerial cable (1, supplied), a scart
cable (2, not supplied).

1.Remove the aerial cable plug from

your TV set. Insert it into the
AERIAL at the back of the video
recorder.

2.Insert one end of the supplied

aerial cable into the RF OUT at
the back of the video recorder
and the other end into the aerial
input socket at the back of the
TV set.

3.Plug one end of a scart cable

into the scart socket AV1(TV)  at
the back of the video recorder
and the other end into the suit-
able scart socket on your TV
reserved for the video recorder operation (see your
TV's operating instructions).

4.Switch on the TV.

5.Insert AC cable into the wall socket.

2

EN

Voltage: 220-240V/50Hz
Power consumption : 20W
Power consumption (Standby): less than 4W
(PWR. in the display switched off)
Rewind time: approx. 100 seconds (cassette E-
180)
Dimensions in cm/ft (WxDxH): 36.0x22.6x9.2 /
1.2x0.3x0.9

Number of video heads : 4
Number of video heads (HIFI): 2
Recording/playback time: 3 hours (SP) (cassette
E-180)
6 hours (LP) (cassette E-180)

• Operating instructions
• Remote control and batteries
• Aerial Cable

The scart or Euro AV cable serves as the universal
connector for picture, sound and control signals. With
this type of connection, there is practically no loss of
quality during the picture or sound transfer.

The severed plug must be destroyed to avoid a possi-
ble shock hazard should it be inserted into a 13A
socket alsewhere.

    RF O

UT

AV1 (TV

)

    AERIA

L

    RF O

UT

AV1 (TV

)

    AERIA

L

    RF OU

T

AV1 (TV

)

    AERIAL

1

2

 HC461BD.qxp  02.2.6  10:12 AM  Page 2