Philips VR969/05 ユーザーズマニュアル
Warning !
7
ENGLISH
Connecting to the mains supply
!
Insert the female plug of the mains cable into the
mains socket ü at the rear of the video recorder.
mains socket ü at the rear of the video recorder.
"
Insert the other plug of the mains cable into the
wall socket.
wall socket.
Your video recorder is now properly connected.
Some notes on operation
•
The video recorder should permanently be connect-
ed to the mains supply to enable programmed
recordings and TV operation. The energy consump-
tion is very low.
ed to the mains supply to enable programmed
recordings and TV operation. The energy consump-
tion is very low.
•
The video recorder is automatically switched on
when inserting a cassette (the z symbol lights up
in the video recorder display) or when pressing the
r button.
when inserting a cassette (the z symbol lights up
in the video recorder display) or when pressing the
r button.
•
If the video recorder is not used for a few minutes,
it is automatically switched off.
it is automatically switched off.
8 8
88:88:8
-:--
D
W
P
EI
8
VPS
S
VHS
STEREO
I
PDC
■
■
z
NICAM II
DEC
LP
MONO HiFi
2 EXTERNAL / DEC.- AV 2
1 EXTERNAL / EURO-AV 1
I
N
L
R
O
U
T
U
T
L
R
AUDIO
S-VHS OUT
RS 232
In case this appliance is supplied with a Safety
Standard Approved mains lead fitted with a non-
rewireable 13 Amp mains plug which, if unsuitable for
your socket, should be cut off and an appropriate plug
fitted by a qualified electrician. The fuse and fuse
holder must be removed from the plug as accidental
insertion of the redundant plug into a 13 Amp socket is
likely to cause an electrical hazard.
Standard Approved mains lead fitted with a non-
rewireable 13 Amp mains plug which, if unsuitable for
your socket, should be cut off and an appropriate plug
fitted by a qualified electrician. The fuse and fuse
holder must be removed from the plug as accidental
insertion of the redundant plug into a 13 Amp socket is
likely to cause an electrical hazard.
Note:
The severed plug must be destroyed to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
If it is necessary to change the fuse in the non-rewire-
able plug, the correct type and rating (3 Amp ASTA or
BSI ap-proved BS 1362) must be used and the fuse
cover must be refitted. If the fuse cover is lost or
damaged the lead and plug must not be used until a
replacement is obtained. Replacement fuse cover
should be obtained from your dealer.
able plug, the correct type and rating (3 Amp ASTA or
BSI ap-proved BS 1362) must be used and the fuse
cover must be refitted. If the fuse cover is lost or
damaged the lead and plug must not be used until a
replacement is obtained. Replacement fuse cover
should be obtained from your dealer.
If a non-rewireable plug or a rewireable 13 Amp (BS
1363) plug is used, it must be fitted with a
3 Amp ASTA or BSI approved BS 1362 fuse. If any
other type of plug is used it must be protected by a 3
Amp fuse either in the plug or at the distribution board.
1363) plug is used, it must be fitted with a
3 Amp ASTA or BSI approved BS 1362 fuse. If any
other type of plug is used it must be protected by a 3
Amp fuse either in the plug or at the distribution board.
Replacement mains lead can be obtained from your
dealer.
dealer.
Important!
The wires in the mains lead are coloured in
accordance with the following code:
BLUE
The wires in the mains lead are coloured in
accordance with the following code:
BLUE
– NEUTRAL
BROWN
– LIVE
As the colours of the wires in the mains lead of
your appliance may not correspond with the
coloured marking identifying the terminals in
your plug, proceed as follows:
Connect the BLUE coloured wire to plug termi-
nal marked with the letter "N" or coloured black.
Connect the BROWN coloured wire to the plug
terminal marked with a letter "L" or coloured red.
In no circumstance must any of the wires be
connected to the terminal marked with a letter
"E", earth symbol
your appliance may not correspond with the
coloured marking identifying the terminals in
your plug, proceed as follows:
Connect the BLUE coloured wire to plug termi-
nal marked with the letter "N" or coloured black.
Connect the BROWN coloured wire to the plug
terminal marked with a letter "L" or coloured red.
In no circumstance must any of the wires be
connected to the terminal marked with a letter
"E", earth symbol
Á
, coloured green or green
and yellow.