Philips VRX342AT ユーザーズマニュアル
If you are having problems with your VCR, check the following list of problems and possible solutions
before requesting service. You may be able to solve the problem yourself.
before requesting service. You may be able to solve the problem yourself.
No power
• Make sure the power plug is completely connected to an AC (alternating current) outlet.
• Make sure the power is turned on.
• Make sure the power plug is completely connected to an AC (alternating current) outlet.
• Make sure the power is turned on.
Power Failure
• Timer recordings and the clock setting may be lost if the power fails for more than one minute. See
• Timer recordings and the clock setting may be lost if the power fails for more than one minute. See
pages 14-17 to reset your clock. See pages 32-39 to reprogram your timer recordings.
A TV program cannot be recorded.
• Check the connections between the VCR, TV, antenna/cable, and Cable Box (if applicable) (pages six-10).
• Make sure the tape has a record tab (page five).
• Check the TV/VCR position (page 26).
• Check the CH3/CH4 switch (pages six-nine).
• Check the connections between the VCR, TV, antenna/cable, and Cable Box (if applicable) (pages six-10).
• Make sure the tape has a record tab (page five).
• Check the TV/VCR position (page 26).
• Check the CH3/CH4 switch (pages six-nine).
The VCR will not perform a timer recording.
• Make sure the recording start and stop times are set correctly (pages 32-39).
• Make sure a tape is in the VCR and the tape has a record tab (page five). If, after programming a timer
• Make sure the recording start and stop times are set correctly (pages 32-39).
• Make sure a tape is in the VCR and the tape has a record tab (page five). If, after programming a timer
recording, you turn off the VCR power without putting a tape in the VCR, the Timer light will blink.
• If the record tab on a tape is missing, the VCR will eject the tape. The Timer light will blink.
• Make sure the VCR power is off.
• Make sure the clock is set (pages 14-17).
• The VCR may not perform or continue a timer recording if a power interruption of more than one
• Make sure the VCR power is off.
• Make sure the clock is set (pages 14-17).
• The VCR may not perform or continue a timer recording if a power interruption of more than one
minute occurs during the timer recording, even if the power comes back on afterward.
• If you have a Cable Box, timer recordings are programmed differently. (See page eight for details.)
• It is best to finish programming a timer recording at least five minutes before the recording is scheduled
• It is best to finish programming a timer recording at least five minutes before the recording is scheduled
to begin.
• 12 PM is noon; 12 AM is midnight.
There is no playback picture or the playback picture is noisy or contains streaks.
• Make sure the TV and the Cable Box, if applicable, are on the same channel as the VCR’s CH3/CH4
• Make sure the TV and the Cable Box, if applicable, are on the same channel as the VCR’s CH3/CH4
switch (pages six-nine).
• Make sure the VCR is in VCR position (page 26). The VCR light will appear on the display panel of the
VCR when the VCR is in VCR position.
• Make sure channel 3 or 4 is properly adjusted at the TV.
• Adjust the tracking (page 45).
• Adjust the tracking (page 45).
The VCR cannot be controlled with the remote control.
• Make sure the VCR light appears on the VCR display panel. If it does not, press the VCR/TV button
• Make sure the VCR light appears on the VCR display panel. If it does not, press the VCR/TV button
once.
• Aim the remote control directly at the VCR’s remote sensor (page 26).
• Remove all obstacles between the remote control and the VCR.
• Inspect and/or replace the batteries in the remote control (page five).
• Remove all obstacles between the remote control and the VCR.
• Inspect and/or replace the batteries in the remote control (page five).
The Number buttons won’t work for channels above 69.
• Select CABLE TV at the TUNER SET UP menu (page 12), then let the VCR program the channels.
• Select CABLE TV at the TUNER SET UP menu (page 12), then let the VCR program the channels.
46 Helpful Hints