Philips VR624CAT ユーザーズマニュアル
POWER
EJECT
SPEED
VCR/TV
VCR
TV
CBL
/DBS
SLOW
ENTER
MEMORY
1
2
3
4
5
6
7
8
9
0
CH.
VOL.
ALT.CH
REW
PLAY
F.FWD
REC
/OTR
PAUSE
/STILL
STOP
MUTE
MENU
STATUS
/EXIT
TIME
SEARCH
CLEAR
1
Press the VCR button, then press the POWER button.
The VCR light and the PWR. (power) light will appear on the VCR
display panel.
The VCR light and the PWR. (power) light will appear on the VCR
display panel.
2
Turn on the TV. Set it to the same channel as the
CH3/CH4 switch on the back of the VCR. The display shown
below will appear on the TV screen. (If the display does not
appear, check your hookups, then follow the steps on page 12 to
set up channels and page 15 to select a language.)
CH3/CH4 switch on the back of the VCR. The display shown
below will appear on the TV screen. (If the display does not
appear, check your hookups, then follow the steps on page 12 to
set up channels and page 15 to select a language.)
3
Within 60 seconds, press the PLAY/o button or the
STOP/p button to select English or Spanish on-screen
displays and menus.
STOP/p button to select English or Spanish on-screen
displays and menus.
4
Press the MENU button. The display shown below will appear.
SELECT op
→
ENGLISH ON
ESPAÑOL
ESPAÑOL
MAKE SELECTION OR
PUSH MENU TO CONTINUE
PUSH MENU TO CONTINUE
Turning on Your VCR 11
5
Within 60 seconds, press the CH(annel) o button to
begin automatic channel programming. AUTO CH PRO-
GRAMMING IN PROCESS PLEASE WAIT will appear on the
screen. The VCR will memorize all available channels. The channel
numbers will appear on the display panel as the VCR scans chan-
nels. When all channels are memorized, CHANNELS ARE SET will
appear on the screen briefly, then TV programming will appear.
Now, when you press the CH(annel) o/p buttons, you’ll only
scan through channels that you receive. You can still select other
channels using the Number buttons.
begin automatic channel programming. AUTO CH PRO-
GRAMMING IN PROCESS PLEASE WAIT will appear on the
screen. The VCR will memorize all available channels. The channel
numbers will appear on the display panel as the VCR scans chan-
nels. When all channels are memorized, CHANNELS ARE SET will
appear on the screen briefly, then TV programming will appear.
Now, when you press the CH(annel) o/p buttons, you’ll only
scan through channels that you receive. You can still select other
channels using the Number buttons.
• To skip this feature and play a tape
immediately, insert a tape with its
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP/p but-
ton. Channels will not be pro-
grammed, and CHANNELS NOT
SET will appear on the screen.
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP/p but-
ton. Channels will not be pro-
grammed, and CHANNELS NOT
SET will appear on the screen.
• When you turn on the VCR again
later, you may see a message
regarding AUTO CLOCK. Details are
on pages 16-19.
regarding AUTO CLOCK. Details are
on pages 16-19.
• If you try to program channels
when no antenna or cable is con-
nected to the VCR, programming
will appear to take place.
Eventually, a NO TV SIGNALS mes-
sage will appear. Connect an anten-
na or cable to the VCR’s ANT(enna)
IN Jack and press the CH(annel) o
button again. You may need to fol-
low the steps on page 12.
nected to the VCR, programming
will appear to take place.
Eventually, a NO TV SIGNALS mes-
sage will appear. Connect an anten-
na or cable to the VCR’s ANT(enna)
IN Jack and press the CH(annel) o
button again. You may need to fol-
low the steps on page 12.
• You may need to repeat the steps
on this page if the power fails.
Helpful Hints
Before turning on your VCR, make sure batteries are in the remote
control and you have connected the VCR and TV correctly.
control and you have connected the VCR and TV correctly.
●
You can not program channels if you are using a Cable Box or a
Direct Broadcast System.
Direct Broadcast System.
●
If you are not using a Cable Box/DBS, the clock may set itself
automatically after you connect the antenna/Cable signal to the
VCR and plug in the power cord. The time will appear on the
display panel.
automatically after you connect the antenna/Cable signal to the
VCR and plug in the power cord. The time will appear on the
display panel.
2
Turn on the TV.
CONNECT ANTENNA OR CABLE
TO VCR
TO VCR
THEN . . .
PUSH CH UP KEY
OR . . .
FOR PLAY ONLY – PUSH STOP
1
3
4
5