Philips VRZ222AT ユーザーズマニュアル
1
Press the VCR button, then the POWER button. The VCR
light and the PWR. (power) light will appear on the display panel.
light and the PWR. (power) light will appear on the display panel.
2
Turn on the TV. Set it to the same channel as the
CH3/CH4 switch on the back of the VCR. The display shown
below will appear. (If the display does not appear, check your
hookups, then follow the steps on page 12 to set up channels and
page 17 to select a language.)
CH3/CH4 switch on the back of the VCR. The display shown
below will appear. (If the display does not appear, check your
hookups, then follow the steps on page 12 to set up channels and
page 17 to select a language.)
3
Within 60 seconds, press the PLAY/o button or the
STOP/p button to select English or Spanish on-screen
displays.
STOP/p button to select English or Spanish on-screen
displays.
4
Press the MENU button. The display shown below will appear.
SELECT op
→
ENGLISH ON
ESPAÑOL
ESPAÑOL
MAKE SELECTION OR
PUSH MENU TO CONTINUE
PUSH MENU TO CONTINUE
CONNECT ANTENNA OR CABLE
TO VCR
TO VCR
THEN . . .
PUSH CH UP KEY
OR . . .
FOR PLAY ONLY – PUSH STOP
Turning on Your VCR 11
5
Within 60 seconds, press the CHANNEL o button to
begin automatic channel setup. AUTO SET PROCEEDING
PLEASE WAIT will appear on-screen. The VCR will memorize all
available channels. When all channels are programmed, CHAN-
NELS ARE SET will appear on-screen briefly, then TV program-
ming will appear.
Now, when you press the CHANNEL o/p buttons, you’ll only
scan through channels that you receive.
begin automatic channel setup. AUTO SET PROCEEDING
PLEASE WAIT will appear on-screen. The VCR will memorize all
available channels. When all channels are programmed, CHAN-
NELS ARE SET will appear on-screen briefly, then TV program-
ming will appear.
Now, when you press the CHANNEL o/p buttons, you’ll only
scan through channels that you receive.
• To skip this feature and play a tape
immediately, insert a tape with its
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP button.
Channels will not be programmed,
and CHANNELS NOT SET will
appear on-screen.
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP button.
Channels will not be programmed,
and CHANNELS NOT SET will
appear on-screen.
• If you try to set up channels when
there is no antenna or cable con-
nected to the VCR, programming
will appear to take place, but even-
tually a NO TV SIGNALS message
will appear. Connect an antenna or
cable to the VCR’s ANT(enna) IN
Jack and try again. You may need
to follow the steps on page 12.
nected to the VCR, programming
will appear to take place, but even-
tually a NO TV SIGNALS message
will appear. Connect an antenna or
cable to the VCR’s ANT(enna) IN
Jack and try again. You may need
to follow the steps on page 12.
Helpful Hints
1
3
4
Before turning on your VCR, make sure batteries are in the
remote control and the VCR and TV are connected correctly.
remote control and the VCR and TV are connected correctly.
●
Follow the steps on this page only when you plug the VCR
power cord into the wall outlet for the first time.
power cord into the wall outlet for the first time.
●
You can not set up channels if you are using a Cable Box or a
Direct Broadcast System.
Direct Broadcast System.
2
Turn on the TV.
5
REW
PLAY
POWER
VCR PLUS+
SPEED
VCR
TV
MUTE
VCR/TV
CHANNEL
VOLUME
REC/OTR
STATUS/EXIT
MEMORY
PAUSE/STILL
MENU
CLEAR
EJECT
STOP
F.FWD
1
2
3
4
5
6
7
8
9
0
+100
VRZ222 layout 4/8/99 10:19 PM Page 11