JVC 0302MNV*ID*JVE ユーザーズマニュアル
Masterpage:Right-NoTitle0
EN
39
Filename [HRS5950EU4-EN.fm]
Page 39
December 4, 2001 5:11 pm
* The default setting is bold in the table below.
8
S-VHS
ON
OFF
OFF
Your recorder can record in S-VHS (Super VHS), S-VHS ET or VHS.
● To record in S-VHS:
Set “S-VHS” to “ON”. Then, insert a cassette marked “S-VHS”. The S-VHS
indicator lights up on the front display panel.
The S-VHS recording mode is selected.
indicator lights up on the front display panel.
The S-VHS recording mode is selected.
● To record in S-VHS ET on a VHS cassette:
See “Super VHS ET (S-VHS ET)” on page 20.
● To record in VHS:
Insert a cassette marked “VHS”.
Press S-VHS ET on the recorder. You can check the current setting (“S-VHS ET :
ON” or “S-VHS ET : OFF”) if “O.S.D.” is set to “ON” (
Press S-VHS ET on the recorder. You can check the current setting (“S-VHS ET :
ON” or “S-VHS ET : OFF”) if “O.S.D.” is set to “ON” (
墌
pg. 37). If “S-VHS ET :
ON” appears on the TV screen, press S-VHS ET again in about 5 seconds to set
it to “OFF”.
The VHS recording mode is automatically selected regardless of the “S-VHS”
mode setting.
it to “OFF”.
The VHS recording mode is automatically selected regardless of the “S-VHS”
mode setting.
● To record in VHS on an S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front
display panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off.
The VHS recording mode is selected.
display panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off.
The VHS recording mode is selected.
NOTE:
When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS
indicator lights up on the front display panel regardless of the “S-VHS” mode setting.
indicator lights up on the front display panel regardless of the “S-VHS” mode setting.
8
COLOUR SYSTEM
PAL/NTSC
MESECAM
MESECAM
You can play back PAL, NTSC and MESECAM tapes, or record PAL and
SECAM* signals on this recorder. Select the appropriate colour system.
SECAM* signals on this recorder. Select the appropriate colour system.
* SECAM signals will be recorded as MESECAM on this recorder; MESECAM is the
designation for tapes with SECAM signals that have been recorded on a
MESECAM-compatible PAL video cassette recorder.
MESECAM-compatible PAL video cassette recorder.
PAL/NTSC
:
To record PAL signals, or play back a PAL or NTSC tape.
MESECAM
:
To record SECAM signals, or play back a MESECAM tape.
NOTES:
● It is not possible to record in S-VHS if “MESECAM” is selected. The recording mode is
forced to change to VHS.
About NTSC Playback
● Some TVs shrink the picture vertically and place black bars at the top and bottom of
the TV screen. This is not a malfunction on the part of either the video recorder or the
TV.
TV.
● The picture may roll up and down. This can be corrected using the V-HOLD control
found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD
control.)
control.)
● The counter and tape remaining time readings will be incorrect.
● During search, still, or frame-by-frame playback, the picture will be distorted, and
there may be a loss of colour.
● Depending on the type of TV, the top and bottom portions of superimposed displays
may be cut off during NTSC playback.
䡵 AUTO POWER OFF
3H
OFF
OFF
When this function is set to “3H”, the recorder is turned off automatically if no
operation is done within 3 hours. “AUTO POWER OFF IN 3 MIN” appears on
the screen 3 minutes before the recorder is turned off.
operation is done within 3 hours. “AUTO POWER OFF IN 3 MIN” appears on
the screen 3 minutes before the recorder is turned off.
HRS5950EU1-EN.book Page 39 Tuesday, December 4, 2001 5:32 PM