JVC 0302MNV*ID*JVE ユーザーズマニュアル
Filename [HRS5950EU4-EN.fm]
Masterpage:Left
48
EN
Page 48
February 8, 2002 2:32 pm
SUBSIDIARY SETTINGS (cont.)
Video Channel Set
Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the
RF cable.
RF cable.
If you have connected the recorder to your TV via the AV connection (
墌
pg. 9), since you do not need the video
channel you have to set the video channel to off.
If you have connected the recorder to your TV via the RF connection (
If you have connected the recorder to your TV via the RF connection (
墌
pg. 9), you have to set the correct video
channel.
A
Access the Video Channel Set mode.
Hold down
0 on the recorder until the front display
panel shows the following.
B
Set the RF output system.
The blinking number on the display indicates the RF
output system of your country.
output system of your country.
● If you have selected MAGYARORSZÁG, CESKÁ REPUBLIKA,
POLSKA or OTHER EASTERN EUROPE for the country setting
(
(
墌
pg. 10, 13), press
rt
to set to “2”.
● For other countries, set to “1”. Then press OK.
(1: B/G 2: D/K)
C
Set the video channel.
With AV Connection
Press PR – until the front display panel shows “1 – –” (or
“2 – –”).
Press PR – until the front display panel shows “1 – –” (or
“2 – –”).
● Now the video channel is set to off.
With RF Connection
Press PR + or – to set the video recorder to a vacant
channel between 22 and 69 which is not occupied by
any local station in your area.
Press PR + or – to set the video recorder to a vacant
channel between 22 and 69 which is not occupied by
any local station in your area.
(Example) If channel 50 is available in your area
Then set your TV to UHF channel 50.
● If the two vertical white bars appear
clearly on the TV screen as shown to
the right, go to step 4.
the right, go to step 4.
● If the two vertical white bars do not
appear clearly, re-set the video
recorder to another vacant channel
and try again.
recorder to another vacant channel
and try again.
NOTES:
● If you set the video recorder to a channel which is occupied by
a local station or has neighbouring channels that are occupied
by local stations, the picture reception quality will be affected
and some interference noise will appear on the TV screen. Be
sure to select a vacant channel which has no broadcast on
neighbouring channels.
by local stations, the picture reception quality will be affected
and some interference noise will appear on the TV screen. Be
sure to select a vacant channel which has no broadcast on
neighbouring channels.
● If you cannot obtain the two vertical white bars clearly with
any channel between 22 and 69, consult your JVC dealer.
D
Exit the Video Channel Set mode.
Press OK on the remote control.
IMPORTANT
Perform the following steps only if —
— Video Chennel Set has not been done correctly by the Auto Set Up function (
墌
pg. 10),
— interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your
area.
— you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.
area.
— you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.
Before performing the following steps:
Make sure the recorder’s power is off and there is no cassette inserted in the recorder.
With AV Connection
To view picture signals from the video recorder, set
your TV to its AV mode.
With RF Connection
The channel on which the TV screen in step 3 appears
clearly is your video channel.
To view picture signals from the video recorder, set
your TV to the video channel.
To view picture signals from the video recorder, set
your TV to its AV mode.
With RF Connection
The channel on which the TV screen in step 3 appears
clearly is your video channel.
To view picture signals from the video recorder, set
your TV to the video channel.
HRS5950EU4-EN.fm Page 48 Friday, February 8, 2002 2:32 PM