Accusplit 625M8D ユーザーズマニュアル

This unit has five modes: Stopwatch, Auto Repeat Countdown 

Timer, Dual Display Countdown Timer, Pacer, and Preset 

Countdown Timer.

Press C (MODE) to change between modes. Note: Timing must 

be stopped and reset to zero to change modes. 

1.  Press C to move the cursor to point to

2.  Press A to start stopwatch

3.  Press B repeatedly to remember the last 8 splits 

  •  Lower display shows cumulative split and upper  

    display shows lap split

  •  After 5 seconds, the unit will unlock splits to display  

    current running split time

4.  Press E to recall the last 8 splits 

5.  Press A to stop counting

6.  Press B to reset to zero

1.  Press C to move the cursor to point to

2.  Press A to start counting 

3.  Press A repeatedly to remember the last 8 time-cuts

4.  Press E to recall the last 8 times-outs 

5.  Press A to stop counting

6.  Press B to reset to zero

1.  Press C to move the cursor to point to

AUTO

2.  Press D to enter set mode

  •  Press B to set hours, E to set minutes, A to set seconds

  •  Press A & B at the same time to reset digits to zero

    ACCUSPLIT®
       ALLIANCE

™

 625M8D

3.  Press A to start countdown timing

4.  Press E to show the time from start ( )

5.  Press E again to return to countdown timing ( )

6.  Press A again to stop counting

7.  Press B to return to the original setting

8.  When time is up, the unit will beep once, then start  

  counting again. The number of cycles completed is  

  recorded in brackets in upper left of display. 

1.  Press C to move the cursor to point to

 

DUAL

2.  Press E to change the dual display timer mode (SU  

  or Id or UP)

3.  Press D to adjust the timer on the lower display

  Press D again to adjust the timer on the upper display

  •  Press B to set hours, E to set minutes, A to set seconds

  •  Press A & B at the same time to reset digits to zero

  •  Press D again to complete the settings

4.  SU - Two countdown timers work simultaneously

  •  Press A to start  

  •  Press A to stop (STOP: flashes)

  •  Press B to reset to the original settings

  Id - Two countdown timers work independently

  •  Press A to start/stop lower display

  •  Press B to start/stop upper display

  •  Press A & B at the same time to reset to the original  

    settings

    UP - Two count up timers work independently

  •  Press A to start/stop lower display (STOP: flashes  

    when stopped)

  •  Press B to start/stop upper display (STOP: flashes  

    when stopped)

  •  Press A & B at the same time to reset to zero

1.  Press C to move the cursor to point to

 

PACE

2.  Press D to adjust the frequency

  •  Press A to increase the digits

  •  Press B to decrease the digits

3.  Press A to start pacer

4.  Press A again to the stop

5.  Press B to reset to zero

6.  Press E to turn the pacer’s beep ON or OFF  

  and the symbol (((•))) will appear or disappear

7.  Upper display shows count up timer

1.  Press C to move the cursor to point to (1-60)

2.  Turn the rotary switch to the desired minutes (1-60)

3.  Press A to start countdown timing

4.  Press A again to stop countdown timing

5.  Alarm Sounds

6.  Press B to return to the original setting

1.  When the time is not up.

  a.  Press E to check elapsed time ( )

  b.  Press E again to return to countdown ( )

2.  When the time is over,

  a.  Press E to check the time from start ( flashes)

  b.  Press E again to show overtime ( flashes)

RESET/SPLIT

RECALL

UP/DOWN

START/STOP

ROTARY 

SWITCH

MODE

SET