Festool PI574422 ユーザーズマニュアル

Supplemental Owner’s Manual 

21

Motor does not start 

 

►

Make sure the power switch is off before plugging in the tool.

 

►

Check that the cord is properly plugged into an outlet.

 

►

Make sure the Plug-it connector is properly inserted and fully tightened.

 

►

Make sure the outlet has power. Check the circuit breaker or try another outlet.

 

►

If used with a Festool dust extractor, make sure the selector switch is pointing to “Auto”. 

The auxiliary outlet on the dust extractor has power only when the selector is at Auto.

 

►

Inspect the power cord (including extension cords) for damage or missing prongs.

 

►

The motor brushes may have worn and need replacement. 

Plunging action is not 

smooth

 

►

Clean the linear rails and bronze bearings of the plunge slide, and make sure they are 

 

►

Inspect the linear bearings for damage. Improper insertion of the fence body onto the 

motor housing can damage the linear bearings.

Domino tenons are too 

loose

 

►

Make sure you hold the Domino joiner firmly in position at the front handle and loosely 

at the rear handle while plunging the mortise slot. It is not uncommon for new users to 

experience this problem, and is a matter of refining your technique for plunging mortises.

 

►

Plunging too fast can cause the mortise slot to be enlarged. Slow down the plunge rate.

 

►

Make sure the mortise width setting is correct.

 

►

Make sure you are using the correct mortising bit for the size of the Domino tenon.

 

►

Check the mortising bit to ensure it is not bent or has a broken tip. A bent bit will make a 

thicker and wider mortise slot than desired. 

 

►

The Domino tenons may have shrunk in an overly dry or warm environment. This is 

normal wood movement.

Domino tenons are too 

tight

 

►

The tenons are intended to be snug fitting, and may require a light tap with a mallet to 

insert them. This is what affords such high precision for Domino tenon joinery.

 

►

The most common cause for this is that the tenons are stored in a humid environment, 

and they have swelled from moisture absorption. Store the tenons in a cool dry envi-

ronment. (Swollen tenons can be re-dried by heating them to 10 to 15 degrees above 

ambient temperature for a short period.)

 

►

The mortising bit may have been improperly sharpened or sharpened too many times. 

Replace the bit. 

Workpiece joints are 

misaligned horizontally

 

►

Make sure the workpiece is securely clamped before plunging.

 

►

Retract the locating pins when not in use.

 

►

Check the calibration of the horizontal position gauge (sight gauge).

 

►

Don’t plunge the mortising bit into the work too fast. This may cause the joiner to move 

during the plunge.

 

►

Make sure the friction pads on the front of the joiner are not worn, damaged, or missing.

Workpiece joints are 

misaligned vertically

 

►

Take care not to tilt the joiner while plunging.

 

►

If the mortise slots were registered from the bottom of the baseplate, make sure there is 

no dust or debris under the joiner or workpiece.

 

►

Make sure the fence is properly locked at the desired height setting.

 

►

Inspect the fence height adjustment lock to ensure it is not broken (slipping). 

Tilted or misaligned 

mortise slots

 

►

Make sure the fence is set to the correct angle (e.g. 90 degrees).

 

►

Make sure to hold the Domino joiner firmly to the work surface.

 

►

Plunging too slow can cause the mortise slots to be tilted slightly.

Workpiece joint won’t 

close (gaps between 

pieces)

 

►

Make sure the proper plunge depth is set.

 

►

Make sure the mortising bit is not broken.

 

►

Make sure the joiner is tight to the face of the workpiece.

 

►

The mortising bit may have been sharpened too many times and is too short.

 

►

Excessive dust may be present inside the linear slide.

 

►

Excessive glue may be present at the bottom of the mortise.

Tearout or rough mortise 

slots

 

►

Plunging speed too fast. Slow down the rate of your plunge.

 

►

Low-grade materials and plywoods will tear out more than solid woods. Decreasing your 

plunging speed will improve the results but may not eliminate the problem completely.

 

►

Dull or broken mortising bit.

Tapered mortise slot. The 

Domino tenon fits only 

part way into the slot

 

►

The plunge speed is too fast and the bit is not cutting the sides properly. Slow down the 

plunge speed.