JVC BR-DV3000U ユーザーズマニュアル
28
PREPARATION
–
Selecting the NTSC/PAL signal system
–
This unit supports both the NTSC and PAL signal system.
Before inputting analogue signals (composite or YC separate video signals), please select the
signal system.
Before inputting analogue signals (composite or YC separate video signals), please select the
signal system.
Mini
PROFESSIONAL
REC
PLAY
REW
STOP
DVCAM NTSC
PAL REC INH.
CH-1/3
CH-2/4
BR-DV3000
A.DUB
OPERATE
INPUT SEL.
REMOTE SEL.
MIC
SERIAL
WIRELESS
9PIN
LINE
DV
Y/C
NTSC
indicator
indicator
OPERATE
button
button
PAL
indicator
indicator
VIDEO
LINE
Y/C
2/4
IN
OUT
REMOTE
SERIAL
9PIN
NTSC/PAL
NTSC
PAL
DC12V
NTSC/PAL switch
STEPS
1.
Set the unit to the OPERATE OFF mode.
2.
Please select the signal system with the NTSC/PAL switch on the rear panel.
3.
Press the OPERATE button to engage the OPERATE ON mode. Either the NTSC or
PAL indicator on the front will then light up, according to the NTSC/PAL switch set-
ting.
PAL indicator on the front will then light up, according to the NTSC/PAL switch set-
ting.
Memo
• In the playback mode, the signal system of the tape is automatically identified, regardless of the
NTSC/PAL switch setting.
• During DV signal input, the signal system of the input signal is automatically identified, regardless of
the NTSC/PAL switch setting.
• When the unit enters the STOP mode, the NTSC/PAL switch setting will be engaged.
• If a tape recorded in both NTSC & PAL signal systems is played, the video, audio or time code may
• If a tape recorded in both NTSC & PAL signal systems is played, the video, audio or time code may
be distorted at the position where the signal system is switched.
• When the signal system of the tape and the NTSC/PAL setting differ, video and sound output will be
upset for about 5 seconds after playback starts or stops.
• NTSC/PAL signal system conversion is not possible.
29
PREPARATION
–
OPERATION LOCK mode
–
This unit comes with an operation lock function to prevent unintended, erroneous operation.
In the OPERATE LOCK mode, the buttons on the main unit and the slide switch are invalid.
However, OPERATE ON and MENU operations are still possible.
In the OPERATE LOCK mode, the buttons on the main unit and the slide switch are invalid.
However, OPERATE ON and MENU operations are still possible.
– – – S Y S T E M [ 2 / 2 ] – – –
D C
I N MO D E
O P E O F F
O P E R A T I O N
L O C K
O N
P A G E B A C K
SYSTEM (2/2) menu
– – – S Y S T E M [ 2 / 2 ] – – –
D C
I N MO D E
O P E O F F
O P E R A T I O N
L O C K
O N
P A G E B A C K
O P E R A T I O N L O C K
䡵 To set the unit to the OPERATION LOCK mode:
Set the OPERATION LOCK item of the SYSTEM (2/2) menu to ON.
☞
Page 54, “Setting the Menu”
● In the OPERATION LOCK mode, when a button on the unit is
pressed, “OPERATION LOCK” will be displayed on the monitor
for about 3 seconds.
for about 3 seconds.
䡵 To turn off the OPERATION LOCK mode:
Set the OPERATE LOCK item of the SYSTEM(2/2) menu to OFF.
If the EJECT button is pressed while the VTR is in the OPERATE
LOCK mode, "OPERATION LOCK" will be displayed. However,
pressing the EJECT mode button persistently will eventually bring
on the MENU screen.
LOCK mode, "OPERATION LOCK" will be displayed. However,
pressing the EJECT mode button persistently will eventually bring
on the MENU screen.