Meyer Sound DS-2 ユーザーズマニュアル
D-2 Control Electronics Unit
analog OR condition, automatically tracks
the power amplifier with the greatest out-
put voltage swing to control the system
protection limiters.
the power amplifier with the greatest out-
put voltage swing to control the system
protection limiters.
Also provided is a switch-defeatable
crossover (Mode switch) and line-level out-
put to drive subwoofer systems, with a sub
polarity switch to facilitate aligning the
subwoofers with the main system. The sub
switches and other setup controls are lo-
cated behind a cover plate on the D-2 front
panel, providing a means for securing the
system installer’s presets.
put to drive subwoofer systems, with a sub
polarity switch to facilitate aligning the
subwoofers with the main system. The sub
switches and other setup controls are lo-
cated behind a cover plate on the D-2 front
panel, providing a means for securing the
system installer’s presets.
The DS-2 loudspeaker operates as a
system with the D-2 Control Electronics
Unit (one per channel). Optimized for the
DS-2 and pre-aligned at the factory, the D-2
contains active crossover networks, fre-
quency response and phase response align-
ment circuitry, and Meyer Sound’s exclu-
sive SpeakerSense™ driver protection
circuitry, incorporating peak and RMS
signal limiting as well as excursion protec-
tion. A single-channel device operating at
line level, the D-2 is intended to be the
final component in the signal chain before
the power amplifier.
Unit (one per channel). Optimized for the
DS-2 and pre-aligned at the factory, the D-2
contains active crossover networks, fre-
quency response and phase response align-
ment circuitry, and Meyer Sound’s exclu-
sive SpeakerSense™ driver protection
circuitry, incorporating peak and RMS
signal limiting as well as excursion protec-
tion. A single-channel device operating at
line level, the D-2 is intended to be the
final component in the signal chain before
the power amplifier.
The D-2 SpeakerSense circuitry protects
the DS-2 loudspeaker components from
damage due to overheating or excessive
excursion under high power conditions.
This unique circuit continuously monitors
the power applied to the DS-2 drivers, and
limits the signal output when the safe oper-
ating areas of the drivers are exceeded.
Until the onset of overload, the Speaker-
Sense circuitry has no effect on the signal.
damage due to overheating or excessive
excursion under high power conditions.
This unique circuit continuously monitors
the power applied to the DS-2 drivers, and
limits the signal output when the safe oper-
ating areas of the drivers are exceeded.
Until the onset of overload, the Speaker-
Sense circuitry has no effect on the signal.
The D-2 SpeakerSense circuit incorpo-
rates Meyer Sound’s new MultiSense™
function, which allows the use of multiple
power amplifiers having different channel
gains and/or power ratings. The D-2 accom-
modates up to four amplifiers, and provides
separate Sense inputs for each. Its
MultiSense circuit, which implements an
function, which allows the use of multiple
power amplifiers having different channel
gains and/or power ratings. The D-2 accom-
modates up to four amplifiers, and provides
separate Sense inputs for each. Its
MultiSense circuit, which implements an
Input
Loop
∞
20
10
8
6 5
4
3
2
1
0
Attn dB
U l t r a S e r i e s ™ D - 2
Ex
RMS
Sense
Limit
Power
DS-2 Only
Safe
Min
Max
DS-2 Power
DS-2 & Sub
180
Polarity of
Sub Output
(to B-2A)
0
o
Mode
o
PUSH