JVC 0397MKV*UN*SN ユーザーズマニュアル
28
EN
VIDEO CAPTURE
(cont.)
INTERVAL CAPTURE
The Interval Capture mode is best suited for
capturing images at set intervals from a video
source unit with a JLIP connector.
capturing images at set intervals from a video
source unit with a JLIP connector.
Preparation
•Make sure all units are properly connected
(
Z
p. 12).
•Insert a tape into the video source unit.
Click "Image Format" in "Set-up" and select
"Field Picture" in the Capture Mode.
(
"Field Picture" in the Capture Mode.
(
Z
p. 29).
1
Open the menu bar and click "Set-up" —
"Capture Mode" — "Automatic".
•The "Automatic Transfer" window
"Capture Mode" — "Automatic".
•The "Automatic Transfer" window
appears.
2
Select the data to be transferred.
•When you select "Index Image", index
•When you select "Index Image", index
image data (80 x 60 pixels) is transferred
to your computer.
to your computer.
•When you select "Index & Full Image",
both index image data (80 x 60 pixels)
and full image data (768 x 552 pixels) are
transferred to the computer.
and full image data (768 x 552 pixels) are
transferred to the computer.
3
Select "Interval Capture".
4
Set the interval.
•Select the time interval at which pictures
•Select the time interval at which pictures
are captured.
5
Set the number of pictures to be captured
and click "OK".
•From 1 up to 99
and click "OK".
•From 1 up to 99
6
Click "Window" — "VCR" to call up the
VCR Operation Window. Start video
playback a few seconds prior to the point
where you want image capturing to start.
VCR Operation Window. Start video
playback a few seconds prior to the point
where you want image capturing to start.
7
Operate the video source unit via the VCR
Operation window and click the "Transfer"
button at the desired picture.
Operation window and click the "Transfer"
button at the desired picture.
1. The message "No. 1 index image being
transferred" appears while the index image
data is being transferred to the computer.
data is being transferred to the computer.
2. When you select "Index & Full Image" in
step 2, the message "No. 1 full image being
transferred" appears while the full image
data is being transferred to the computer.
transferred" appears while the full image
data is being transferred to the computer.
3. The message "Index No. 2 being scanned"
appears while the video data are fast-
forwarded and played at the time intervals
set in step 4 to scan the video data on the
VCR.
• The image selected when "Transfer" is
forwarded and played at the time intervals
set in step 4 to scan the video data on the
VCR.
• The image selected when "Transfer" is
clicked is captured and subsequent images
are captured at the time interval specified
by the counter value selected in step 4.
are captured at the time interval specified
by the counter value selected in step 4.
• The video source unit enters the Pause
mode when capture is complete.
Set-up
Capture Mode
Image Format
Device Change
Initialize
ID Change
Counter Reset
Device Change
Initialize
ID Change
Counter Reset
Step by Step
Automatic
00:01:23:12F
I
VCR
Capture
Transfer
NOTE:
•Make sure that enough hard disk space is
available on your computer before
executing video transfer.
For full image data space requirements,
executing video transfer.
For full image data space requirements,
Z
p. 24.
•Transfer of index image data/full image
data starts at the image box bordered in
green.
Click and select the desired image box.
green.
Click and select the desired image box.
•When transferring full image data using
the Bitmap image format (
9
.bmp), the
transfer takes a very long time, causing
the video source unit to stop playback
automatically.
the video source unit to stop playback
automatically.